pure Ti
Frictional and Wear Behavior of Commercially Pure Ti, Ti 6Al 7Nb, and SUS316L Stainless Steel in Artificial Saliva at 310 K
... commercially pure Ti (Grade 2), and Ti-6Al-7Nb in arti fi cial saliva and in deionized water were investigated at 310 K using a ball-on-disc type frictional test machine with a Ti ...of ...
10
Fabrication of Bioactive Pure Ti by Microarc Oxidation and Hydrothermal Treatment Methods
... ) of pure Ti(grade 4) were used as the substrates for MAO. Prior to the coating, samples were polished with abrasive paper (#2000), degreased with acetone and rinsed with distilled water. The MAO treatment ...
14
Improved Biocompatibility of Titanium Zirconium (Ti Zr) Alloy: Tissue Reaction and Sensitization to Ti Zr Alloy Compared with Pure Ti and Zr in Rat Implantation Study
... of Ti–Zr alloy by an implantation test in animal bodies in comparison with pure Ti, Zr, and chromium (Cr) implants as positive ...the Ti and Ti–Zr alloy implants were thinner than those ...
8
Chemical Hydrothermal Synthesis of Bioinert ZrO2 TiO2 Films on Pure Ti Substrates and Proliferation of Osteoblast Like Cells
... Although Ti and its alloys are classified into bioinert materials, conduction of living bone occurs on the surface of implanted materials that reside in the body for a long ...
7
Formation of Anatase on Commercially Pure Ti by Two Step Thermal Oxidation Using N2 CO Gas
... Titanium (Ti) and its alloys have excellent properties such as high corrosion resistance and an excellent balance of strength and ductility. They have therefore been used in aerospace, military, electrical and ...
6
Effect of Sn Content on the Corrosion Behavior of Ti-based Biomedical Amorphous Alloys
... spinning method, and the fully amorphous alloys were obtained in the alloys as the Sn content increasing from 0 to 8 at. %. The effects of the Sn addition on the corrosion behavior of the amorphous alloys in phosphate ...
10
Fabrication and characterization of the Ti Ca P composites by vacuum sintering
... cept pure Ti displayed a good cell proliferation and cell attachment behavior as shown in Figure ...On pure Ti surface cells cannot proliferate in such short time ...80% Ti based ...
8
Biologically Modified Titanium Substrates for Improved Surface Bioactivity
... commercially pure Ti surfaces with nanoscale reduced graphene oxide coating, and according to the re- sults, pre-osteoblast cells cultured on the coated samples showed higher cell viability and cell ...
7
Tribological Property of α Pure Titanium Strengthened by Nitrogen Solid Solution
... of Ti materials with no rare metals, nitrogen solid solution strengthening was applied in the fabrication of pure Ti based materials by powder metallurgy ...of Ti-TiN powders, the additive TiN ...
5
Nanoparticles formation mechanisms through the spark erosion of alloys in cryogenic liquids
... Mechanisms of the formation of nanoparticles of some B2 shape memory intermetallic compounds, glass-forming Zr-based alloy, and pure Ti obtained by spark erosion method in liquid nitrogen and argon are ...
8
On the high pressure phase stability and elastic properties of β titanium alloys
... 2 It is important to note that, even in nominally pure Ti, a variety of different transition pressures have been observed for the α→ω transition. The variation has been attributed to the choice of different ...
14
Improved Corrosion Resistance and Thinner Alpha Case Layer on Titanium Casting Using Al2O3 5Ti as Investment Material
... The Ti castings prepared with the two different investment materials were used as the working electrode, and pure Ti grounded with SiC paper was also used as it for the ...
5
Mechanical Properties of Harmonic Structured Composite with Pure Titanium and Ti 48 at%Al Alloy by MM/SPS Process
... ne Ti 48Al powder, mechanical milling was performed at a ball-to-powder weight ratio of 3 : 1 and an MM time of 54 ...of pure Ti powder and Ti48Al ...and pure Ti was sintered using ...
5
Mechanical Property, Fatigue Strength and Clinical Trial of Dental Cast Ti 15Zr 4Nb 4Ta Alloy
... the Ti–15Zr– 4Nb–4Ta alloy with those of commercially available pure Ti grade 2 and Ti–6Al–V alloy, the micro-Vickers hardness, tensile property at room temperature, concentration of metal ...
6
Application of High Pressure Gas Jet Mill Process to Fabricate High Performance Harmonic Structure Designed Pure Titanium
... fine-sized pure Ti powder via jet milling followed by spark plasma ...The pure Ti compacts with a harmonic structure exhibited a significant enhancement in the strength without compromising the ...
6
Growth Kinetics of β Ti Solid Solution in Reaction Diffusion
... type pure metal Ti–X diffusion couples were set in a stainless steel holder and pressed by ...with Ti foils as gettering materials to remove oxygen, nitrogen and hydro- carbons from the annealing ...
6
Active Hydroxyl Groups on Surface Oxide Film of Titanium, 316L Stainless Steel, and Cobalt Chromium Molybdenum Alloy and Its Effect on the Immobilization of Poly(Ethylene Glycol)
... The materials employed in this study were a commer- cially pure Ti with grade 2, cp-Ti, (Rare Metallic Co., Ltd., Japan), a type 316L austenitic stainless steel, SS, (Daido Steel Co., Ltd., Japan), ...
7
Micro Arc Oxidation of Ti 15Zr 7 5Mo Alloy
... Ti-15Zr-7.5Mo alloy buttons were prepared by arc melting from commercially pure Ti (CP Ti; Grade 2), pure Zr (99.5%), and pure Mo (99.9%) under an Ar atmosphere on a wa- ...
5
Cyclic Properties of Protium Absorption Desorption in Ti Cr V Alloys
... Figure 1 shows the PC diagram at 313 K of pure V metal (x = 100) measured for up to the 50th cycle. V metal absorbed about 3.7 mass% protium but desorbed only about 2.2 mass% protium at the 1st cycle. The PC ...
5
Effect of Mold Material and Binder on Metal Mold Interfacial Reaction for Investment Castings of Titanium Alloys
... A number of investigations have already been made on the evaluation of different oxide molds against molten titanium and titanium alloys. Suzuki et al. proposed that pure yttria was a strong candidate as a mold ...
6