Steel sheet
Lap joint dissimilar welding of aluminium and steel sheet using tig welding
... between steel and aluminium alloys by using self-brazing technique where the molten zone of steel is controlled to form a partial penetration during lap joint welding between steel and aluminium ...
24
The Effects of Induction Motor’s Steel Sheet Thickness on Efficiency, Losses and Electrical Cost
... Loss, material type and thickness are the important parameter in designing an induction motor’s electrical steel sheet. Loss is defined as; of the induction motor power supply in the system of 3-phase ...
7
Steel Sheet Surface Image Denoising Based on CUDA
... Abstract. The steel sheet surface image denoising problem is addressed based on powerful parallel computing of GPU. We present some experiments comparing three denoising methods of original median ...
7
Temperature Dependency of Diffusional Transformation Texture Development in Steel Sheet
... The temperature dependency of diffusional transformation texture development in steel sheet was investigated by electron backscatter diffraction. The site of the precipitated pro-eutectoid ferrite (PF) ...
7
Effect of Microstructure before Cold Rolling on Texture and Formability of Duplex Stainless Steel Sheet
... stainless steel and mild steel sheets, it is well known that the r-value is improved by promotion of the h111i == ND recrystallization ...stainless steel sheet has been explained by the ...
9
Corrosion Performance of Conversion Treatments for Electrogalvanised Steel Sheet
... electrogalvanised steel sheet: 1) Cr(III) and Zr complexes layer, 2) Ce(III) layer, 3) Ce(III)/Ce(IV) double layer, 4) Cr(VI) chromating was investigated, and its results compared with those from the tests ...
23
Impact of Young’s modulus degradation on springback calculation in steel sheet drawing
... a steel sheet drawn part is affected by stiffness degradation, which results from the material damage evolved during the forming ...stainless steel E N ...f sheet metal forming. Its influence ...
9
Fine-structured Morphology of Silicon Steel Sheet after Laser Surface Alloying of Sb Powder
... electrical steel sheet formed in an industrial process is composed of iron oxide(s), silica, alumina and other complex ...electrical steel sheets is already oxidized, this may be an additional source ...
7
Experimental study of strain fields during shearing of medium and high-strength steel sheet
... Methods: In this work, strain fields were continuously measured during shearing of a medium and a high strength steel sheet, using digital image correlation. Preliminary studies based on finite element ...
16
Elasto Plasticity Behavior of High Strength Steel Sheet in Biaxial Stress Path Change
... The elasto-plasticity behavior of a high-strength steel sheet of 980 MPa-TS was investigated by performing biaxial tension experiments. In order to evaluate the accuracy of constitutive models of plasticity ...
5
Effect of Pretreatment Film Composition on Adhesion of Organic Film on Zinc Coated Steel Sheet
... the steel sheet after heating, and was rated as one point when these films exfoliated in parallel without following the steel sheet after ...
9
Determination of Weld loads by using Design of Experiments for low carbon steel sheet for Automobile Application
... To develop and analysis the failure mechanisms or criterion of spot weld for direct and indirect resistance spot welding we performed the strength test using lap – shear , samples made for low carbon steel ...
6
Effects of Coiling Temperature on the Microstructures, Mechanical Properties and Textures of 08Al Deep Drawing Steel Sheet
... drawing steel sheet for the hot-rolling microstructure is that grains are homogeneous and fi ne, and meanwhile the cementites at GBs should not be ...experimental steel coiled at the temperature ...
7
A new way to evaluate steel sheet surfaces
... Coated steel products are used widely in the construction industry due to their decorative appearance and the fact that the coating protects the underlying steel from the effects of environmental ...coating ...
6
Impact of Crystallographic Surface on the Planar Anisotropy of Tightening Reaction in 316 Stainless Steel Sheet
... ABSTRACT: The impact of crystallographic surface on planar anisotropy in strain and low cycle exhaustion was explored for tests machined along 0, 45 and 90° edge regarding the moving heading of hot rolled and tempered ...
13
Application of Stop and Play Models to the Representation of Magnetic Characteristics of Silicon Steel Sheet
... This paper first compares the ability of the stop and play models to represent hysteretic relations from to in a sil- icon steel sheet. The present paper then proposes a combination of the stop and play ...
5
Fuzzy logic based modeling of CO2 laser cutting for stainless steel sheet
... have been developed expert system using fuzzy logic model to predict the CO2 laser cutting process parameter on 2.5mm thickness stainless steel sheet. The fuzzy logic model developed in MATLAB using the ...
5
Lap joint dissimilar welding of aluminium and steel sheet using tig welding
... between steel and aluminium alloys by using self-brazing technique where the molten zone of steel is controlled to form a partial penetration during lap joint welding between steel and aluminium ...
24
Quantitative characterisation of surface finishes on stainless steel sheet using 3D surface topography analysis
... stainless steel designation, the finish produced by the 2B process route, has been chosen to demonstrate the primary parameter set ...Stainless steel sheet is usually formed using a combination of ...
222
Ultrasonic characterisation of rolled aluminium and steel sheet correlated with electron backscatter diffraction measurements
... In the presence of a static magnetic field, an elastic deformation, such as that caused by an acoustic wave travelling in a metallic sheet, will induce eddy currents in the skin depth of the sheet as ...
235