Surface Condition
An experimental study on surface state description by wiping motion for the estimation of floor surface condition using indoor search robot
... a surface condition by wip- ing ...the surface hard- ness of each floor materials, measured by Scratch hardness test (Pencil method), which is defined in JIS ...the surface by wiping ...curved ...
9
Thermal Characteristics As Diagnostic Tools To Determine Surface Condition Of Polymeric Insulation Material
... Determine Surface Condition Of Polymeric Insulation Material” and found that it has complied the partial fulfillment for awarding the degree of Bachelor of Electrical Engineering (Industrial Power) ...
24
Route level analysis of road pavement surface condition and truck fleet fuel consumption
... Based on the literature review the payload and the gradient are two of the most influential variables on fuel consumption (Sandberg, 1990, Beuving et al., 2004). However, no data about the payload is currently available ...
7
Investigation of Gold Electrodes Surface Condition of Plasma Reactor
... the surface condition of the electrodes used (Figure 1) and the concentration of the ozone produced Figure ...the surface of the electrode is released and takes part in the ozone formation ...
10
Effect of substrate surface condition on thermal cycling behavior of lead-free solders
... of surface finishes on copper ...free surface finish include bare copper, immersion tin, and electroless nickel/immersion gold on copper ...the surface condition of as-received samples with ...
24
DIAGNOSTICS OF WORKPIECE SURFACE CONDITION BASED ON CUTTING TOOL VIBRATIONS DURING MACHINING
... Workpiece surface condition diagnostics based on cutting tool vibration is a relatively ef- fective method when active machining process monitoring is ...the surface state at the stage of production ...
9
Frequency Analysis Technique For Determination Of High Voltage Insulation Material Surface Condition
... the surface of non-conductive parts to ground if a conductive path was ...the surface of the polymeric which is the insulation material that will be used in this ...
24
The Study On The Effect Of Water Composition In Coolant To The Surface Condition Of Workspiece
... the surface quality, shape, dimensional accuracy of a workpiece also the ability in enhancing the tool life, and protecting the workpiece from ...the surface roughness but not on the contribution and effect ...
24
Comparative Study Of Leakage Current On Insulation Surface Condition
... low surface energy, better performance in wet condition and also great mechanical strength to weight ratio which means it is sturdily although it was light in ...
24
Comprehensive model for upgrading two-lane road network
... For Low Volume Roads (LVR) in Saskatchewan (2007), a similar approach to Vermont has been developed [11]. This approach is based on certain Levels of Improvement (LOI), dependant on the roadway geometrics, the current ...
11
The impact of vibration on comfort and bodily stress while cycling
... The point to note is that texture has the lowest weighting of all the different factors, but this more microscopically sized defect is of potentially greater importance and a source of discomfort for cycle traffic. ...
12
Surface Soil Moisture Measurement during Pre Monsoon Season of Imphal Valley, Manipur: using multispectral remote sensing data
... Imphal valley is located in the central part of the state covering an area about 1843 sq. km. It virtually comprises of four districts viz, Imphal East, Imphal West, Bishnupur and Thoubal district. Holding 70% of total ...
10
Creation of a Curatorial Plan for the RIT Archives: A Case Study of the Frans Wildenhain Ceramic Collection
... is condition report #13 23 ...the surface is described in detail so that at a later point people can go back and check if the damage is getting worse, or if the care and handling of the object is stopping ...
112
Effect of Energy Consumption in the Contact Zone on Machining Condition Optimization in Precision Surface Grinding
... (1) Optimization of spindle speed of machine-tool Assuming that the number and topography of active grits in the contact zone remain unchanged (i.e. attrition wear and breakage of abrasive grits will not occur) in an ...
12
Boundary layer flow past a stretching/shrinking surface beneath an external uniform shear flow with a convective surface boundary condition in a nanofluid
... The problem of a steady boundary layer shear flow over a stretching/shrinking sheet in a nanofluid is studied numerically. The governing partial differential equations are transformed into ordinary differential equations ...
7
The Optimal Milling Condition of the Quartz Rice Polishing Cylinder Using Response Surface Methodology
... The results of variance are presented in Table I, II, III and IV. The application of response surface methodology in this experiment was complicated and time consuming. Since all of the coefficients have to be ...
5
Effect of Anisotropy of Surface Energy on the Growth Direction of Solid Phase in Constrained Growth Condition
... Solid/liquid interfacial energy has an effect on the size of a dendrite, such as a dendrite tip radius. It is anisotropy of surface energy that affects the growth direction of solid phase. This study then has been ...
7
Thermochemically activated carbon as an electrode material for supercapacitors
... A small peak at the potentials of 0.85 … 1 V is due to the release of oxygen dissolved in the electrolyte and adsorbed by the surface of the active material [12]. Com- paring the cyclic voltammograms at the scan ...
8
Optimization of the Magnetic Sensor Configuration for JT-60SA Plasma Control
... deceases the reconstruction error [4]. However, the cost of magnetic sensors used for plasma control and for their data acquisition systems in large devices possessing a long discharge is high. Therefore, it is ...
5
Finite element analysis of metal boxes falling which hits the ground
... contact surface area and the peak stress in contact area of brittle material influences the strength of the device seriously [6], so we need analyze the contact stress ...
5