von Mises stress
Investigation of Von Mises Stress and Stress Concentration Factor for Cylinders with Holes in Different Locations and Varying Pressure using Analytical Method and FEA
... The von mises stresses results obtained from ANSYS for different hole locations are tabulated in table ...the von mises stress distribution for different cylinders with different hole ...
7
Maximum von Mises Stress in the Sliding Contact of Coated Bodies
... the stress state in the contact of bi-layered bodies in ...the von Mises stress in the coating, as well as in the ...equivalent stress is influenced by the elastic modulus mismatch ...
12
Fluid structure interaction analysis on failure of Francis turbine runner blades
... the Von-Mises stress distribution in rehabilitated runner is ...the stress concentration come out of the area of blade and crown connection and the amount of stress declined ...of ...
6
Finite Element Analysis for Comparison of Spinous Process Osteotomies Technique with Conventional Laminectomy as Lumbar Decompression Procedure
... maximal von Mises stress of the annulus fi- brosus, and the intradiscal pressures at the index segment (L3‒4) and adjacent seg- ments (L2‒3 and L4‒5) under ...annulus stress at both the index ...
8
CHARACTERISATION OF ALUMINIUM-FLYASH-ALUMINA COMPOSITE FOR PISTON ANALYSIS BY CAE TOOLS
... maximum von mises stress induced in the piston is 312 Mpa, at the inner boss fillet area which due to stress concentration effect and pressure application on top face of the ...The ...
14
Analysis of High Sensitivity MEMS Hydrophone for Underwater Applications
... the stress across the patches when pressure of 1 pascal is applied on the beam , the above stress depicts von mises stress, which uses distortion theory concept which predict failure ...
5
Load Bearing Capacity of Orthopedic Knee Replacement Implant
... ( von mises ) stress and maximum principle stress the streses developed are less than the ultimate tensile strength or ultimate yield strength and ultimate compressive strength of the ...
16
OPTIMIZATION OF TURRET COMPONENTS OF TABLET PRESS MACHINE
... Figure 1,2,3,4,5 shows the constraints and loads, von-Mises stress contour,maximum stress position, maximum principle stress contour, Total deformation contour respectively.. Table 4.1 [r] ...
5
Mechanical Analyses of Multi-piece Mining Vehicle Wheels to Enhance Safety
... The stress/strain analysis was performed through the commercial FE software code ...the stress life approach was ...and stress concentration were also taken into account using endurance-limit ...
318
Towards a Ship Structural Optimisation Methodology at Early Design Stage
... In AVEVA Marine model, the displacements in x-, y- and z- directions were suppressed at fore and aft sides, while all boundaries in FORAN model were restrained from displacements in x-, y- and z- directions. The FE ...
15
Study on transferred impulse and response of steel plate walls under various impulsive loading considering mesh size effects
... as Von Mises stress of SPWs under various blast impulsive loadings are investigated through both material and geometric ...of Von Mises stress, the amount of output impulse and ...
16
Tanker ship structural analysis for intact and damage cases
... This paper is organized as follows: Section 2 presents and methodology applied. The main char- acteristics of the model selected as well as the pro- cess follows to generate the model developed is ex- plained. Section 4 ...
9
Design and Analysis of a Skid for Fuel Tank Bracket of a Truck
... of von Mises stress developed in the static analysis of the solid skid and L shaped skid with three different materials is almost equal and very well below the yield strength of each respective ...
7
Finite Element Analysis of Tibia with Osteogenesis Imperfecta: The Influence of Considering Cancellous Bone in Model Reconstruction
... lower von-Mises stress compared to the cortical-cancellous model, this indicates that the results produced are consistent, which the single model yielding stress-strain response that ...
6
The influence of linear kinematic hardening and non linear combined isotropic kinematic hardening plasticity model on sliding contact
... and stress distributions for Ti- 6Al-4V material using cylinder-on-flat contact configuration FE ...higher stress response, meanwhile Non-Linear Combined Isotropic-Kinematic hardening (NCH) plasticity model ...
6
Fluid-Structure Interaction in Abdominal Aortic Aneurysms: Effect of haematocrit
... on von Mises stress magnitude and distribution, whereas there is a close relation between the haematocrit value and the Wall Shear Stress (WSS) magnitude in ...
16
Meso scale numerical study of composite patch repaired hole drilled steel plate
... (von-Mises) stress of ...(von-Mises) stress and maximum equivalent elastic strain of the steel plate by approximately ...
5
Parametric Study of Beam to Column Bolted Connection with Cellular Beams
... The analysis was carried out on the models and the results were obtained. Non linear dynamic analysis was conducted for the analysis. The study analyzes the deflection, maximum principle stress, and von ...
5
16. Load Analysis of One and Two Piece Rotor of Disc Brakes Using Fea Package
... the Von Mises stress established in the disc for the both solid and ventilated disc with two different materials to enhance performance of the rotor ...
5
Modeling of Tactile Detection of an Artery in a Soft Tissue by Finite Element Analysis
... As shown in Figs. 5, 6, and 8, Von Mises stress graphs were derived for the nodes on top side of models b and c, in comparison to model a, include a peak. The peak for these two graphs is a symptom ...
5