[PDF] Top 20 Addition on the Microstructure and Properties of CoCr Alloys

... The Co-base alloy, rapidly melted by laser heating, did not undergo phase transformation and remained in γ-Co phase. This was because the rapid cooling of the substrate to room temperature caused γ-Co phase to be ... See full document

... the microstructure of stir zone with copper nanoparticles inserted in a groove of 3 mm×1 mm and 3 mm×2 ...the microstructure as shown in ...the microstructure show less reinforcements deposition in ... See full document

... Manufacturing alloys of aluminum for the first group can be used for electrical contacts with proportion purity aluminum of ...by addition (Zinc) impurity to the molten aluminum with percentage of ... See full document

... from crystallite size refinement in the copper matrix structure, produced by ceria dispersion [4]. In according to this, another study observed that ceria may in- crease the hardness of the copper as long its particles ... See full document

... Cr addition on the mechanical properties of as-cast and heat treated alloys in the wide temperature range from room tem- perature to 1773 ...The addition of 5 ... See full document

... phase regions in the as-fabricated ultrafine-grained alloy without WC addition were evaluated in Fig. 6. For the two-phase regions in the ultrafine-grained alloy, sudden displacement excursions (pop-ins) marked by ... See full document

... two-phase microstructure developed in the grain interior is well resolved by the pattern of the elemental distribution where Al is en- riched in the primary Ni 3 Al precipitates and V is enriched in ... See full document

... (Mg) alloys are well known for their superior specific strength and good machinability with ubiquitous applications in automobile and aerospace ...In addition, these lightweight alloys demonstrate ... See full document

... into the Mg matrix during the solution treatment, and then re-precipitated from the matrix as much finer clusters and non-uniformly distributed within grains and along grain boundaries, as shown in Fig. 10. These ... See full document

... an addition of zinc up to ...zinc addition. On the contrary, in rolled-specimens, addition of ...mechanical properties in both strength and ductility ... See full document

... the microstructure and mechanical properties of Al-7% Si ...Al-Si alloys. Microstructure property correlations were car- ried out using SEM-EDS and tensile testing of ...alloys. ... See full document

... Co addition as ...and microstructure properties of rapidly solidified Al-20Si-5Fe alloys by addition of Cr and Zr, results displayed that different size of β and Si particles were ... See full document

... Most spark plasma sintered samples investigated by some researchers are cylindrical with 20 mm diameter [13,14]. Such a small size could present difficulties in preparing suitable samples for measuring physical ... See full document

... the alloys are presented in Table ...the alloys as a function of the titanium contents is shown in Figure ...the alloys is as a result of the wide difference in concentrations of titanium additions ... See full document

... 95Pt-5Ru-based alloys is described in detail in (23, ...The addition of small amounts of Co changes the segregation direction from the binary system to the ternary system and thus results in a reduction of ... See full document

... cleavage planes with cleavage steps of different sizes and river patterns indicated the action of brittle failure. With Yb addition, more and larger cleavage surfaces were observed in Fig. 7(b)–(d), which was ... See full document

... RE addition on the thermal stability of AZ31 alloys, the variation of micro- structure and hardness of AZ31-xRE alloys after solid solution treatment was estimated at elevated ...AZ31-3RE ... See full document

... The weld grain sizes were significantly reduced after FW. The initial average grain sizes were 54.9 μm for A6063 and 65.2 μm for A2017, which noticeably decreased to 2.2 μm and 3.4 μm, respectively (see Figs. 3 and 4), ... See full document

... Ceramic bodies are normally composed two groups of materials: Plastic and non- plastic material. The plastic material is predominantly based on clays and sometimes kaolin, which are essential to the development of ... See full document

... Tensile and hardness measurement results The effect of solidification rate on the mechanical properties such as the tensile and hardness are given on table 1 and Fig 10 respectively. The ultimate strength of ... See full document