tion Failure
A.1. Error Error Categorie Categories s
A.1. Error Error Categorie Categories s
The following listing expla
The following listing expla ins the different error categories and how the error messages areins the different error categories and how the error messages are logged.
logged.
•
• Hardware errorsHardware errors
Monitoring the the individual system elements (modules) and their configuration by the Monitoring the the individual system elements (modules) and their configuration by the firmware. Logging online in
firmware. Logging online in ─
─ DDIAGNOSISIAGNOSIS| O| O VERVIEW VERVIEW(errors present).(errors present).
─
─ DDIAGNOSISIAGNOSIS| H| HISTORYISTORYDDIAGNOSISIAGNOSIS(time-tagged error messages, history).(time-tagged error messages, history).
•
• Software errorsSoftware errors
Monitoring by the firmware and logging online in Monitoring by the firmware and logging online in ─
─ DDIAGNOSISIAGNOSIS| O| O VERVIEW VERVIEWand Dand DIAGNOSISIAGNOSIS | H| HISTORYISTORYDDIAGNOSISIAGNOSIS(behavior of the PLC).(behavior of the PLC).
─
─ PLC | DPLC | DIAGNOSISIAGNOSIS (errors when compiling the application program code, syntax of the(errors when compiling the application program code, syntax of the IL).
IL).
•
• Parameter setting errorsParameter setting errors Are reported online by the
Are reported online by theWebserverWebserver, and offline by, and offline byWEBmicWEBmic..
The input of the parameters is subjected to a plausibility check, error messages are not The input of the parameters is subjected to a plausibility check, error messages are not output.
output.
•
• Operator errorsOperator errors
Are largely excluded by the user interface. You can find further inform
Are largely excluded by the user interface. You can find further information thereto in sec-ation thereto in sec-tion
tion A.3 A.3,, Operator ErrorsOperator Errors..
Operation and Maintenance TM 1703 mic
Operation and Maintenance TM 1703 mic 163163
DC6-013-2.01, Edition 08.2008 DC6-013-2.01, Edition 08.2008
The errors detected by the system are logged on the user interface.
The errors detected by the system are logged on the user interface.
Meaning of the Ax error
Meaning of the Ax error classes (FK):classes (FK):
I
I……internalinternal
E
E ……externalexternal
K
K……communicationcommunication
B
B……module failuremodule failure
List of error messages that are displayed in the diagnosis:
List of error messages that are displayed in the diagnosis:
Error
Error No. No. Error Error Text Text CausCause e RemeRemedy dy FK FK ER ER LEDLED TranTransientsient 000
000 Acknowledgement Acknowledgement error error Station was Station was not not calledcalled Check connection to the Master and pa-Check connection to the Master and pa-rameter setting
rameter setting
Yes No
Yes No *)*)
001
001 Wrong Wrong telegramm telegramm receivedreceived •• Unknown type Unknown type identificatidentificationion
•
• Unknown CASDUUnknown CASDU
The faulty telegram is indicated in The faulty telegram is indicated in Diagno-sis | History DiagnoDiagno-sis, starting with the sis | History Diagnosis, starting with the type identification in hex
type identification in hex
Yes Yes Yes Yes *)*)
002 Error
002 Error during during telegram telegram transmit transmit Pack Pack error error Currently Currently not not implementimplemented ed Yes Yes NoNo *)*) 003
003 Super Super high high prior prior queue queue overflow overflow FIFO overflow at answer for login in dial-FIFO overflow at answer for login in dial-up traffic
up traffic
Overflow of an internal buffer, please Overflow of an internal buffer, please consult your system supplier consult your system supplier
Yes No
Yes No *)*)
004
004 High High prior prior ring ring overflow overflow ACT/CON te ACT/CON telegrams canlegrams cannot be tranot be transmit- nsmit-ted to the remote station
ted to the remote station
•
• Check ILCheck IL
•
• Possibly to many Possibly to many commands receivedcommands received via communication in too short time via communication in too short time
Yes No
Yes No *)*)
005
005 Queue Queue overflow overflow class class 11 Too many data at too slow communicationToo many data at too slow communication (no more than
(no more than 200 telegrams are sent)200 telegrams are sent)
•
• Check ILCheck IL
•
• Check if an input signal Check if an input signal is bouncingis bouncing
Yes No
Yes No *)*)
006
006 Queue Queue overflow overflow class class 2 2 See See error error 005 005 Yes Yes NoNo *)*) 007
007 SIM SIM card card not not availableavailable SIM card not plugged or not pluggedSIM card not plugged or not plugged correctly
correctly
Plug in SIM card correctly under the front Plug in SIM card correctly under the front cover
cover
Yes No
Yes No *)*)
008
008 Errors Errors clearedcleared In the History Diagnosis it is indicated,In the History Diagnosis it is indicated, when the errors
when the errors were resetwere reset
No No
No No *)*)
009
009 Reset Reset by by hardware/power hardware/power on on Power Power supply supply was was switched switched on on No No NoNo
164
164 Operation and Maintenance TM 1703 micOperation and Maintenance TM 1703 mic
DC6-013-2.01, Edition 08.2008 DC6-013-2.01, Edition 08.2008 010
010 Reset Reset by by remote remote command command (ti105) (ti105) Startup Startup command command received received from from Master Master No No NoNo 011
011 Reset Reset by by watchdogwatchdog Watchdog is exceeded and a startup wasWatchdog is exceeded and a startup was performed
performed
Read Diagnosis | History Diagnosis and Read Diagnosis | History Diagnosis and inform Siemens
inform Siemens
No No
No No
012
012 Firmware Firmware disabled disabled (kill) (kill) Internal Internal software software error error
•
• Invalid parameter file loadedInvalid parameter file loaded
•
• Invalid IL loadedInvalid IL loaded
•
• Reload parameter Reload parameter
•
• Reload ILReload IL
•
• If no remedy: carry out a firmware up-If no remedy: carry out a firmware up-date
015 firmware firmware loadedloaded In the History Diagnosis it is In the History Diagnosis it is indicated,indicated, when the fir
when the firmware was updatedmware was updated
Yes No
Yes No
016
016 DCD DCD continuous continuous levellevel •• In multi-point traffic this might happen atIn multi-point traffic this might happen at plugging in the nullmodem cable (mainly plugging in the nullmodem cable (mainly with DELL PC
with DELL PCs)s)
•
• Modem has detected a continous levelModem has detected a continous level
Check
020 Reset Reset after after parameter parameter changingchanging •• A startup was triggered by the user dueA startup was triggered by the user due to a parameter change (on
to a parameter change (on demand)demand)
•
• TM 1703 mic has performed an auto-TM 1703 mic has performed an auto-matic startup in consequence of a matic startup in consequence of a pa-rameter change
022 CconnectioCconnection n 1 1 lossloss •• Connection to the remote station failedConnection to the remote station failed
•
• Wrong IP addressesWrong IP addresses
Check IP addresses and connection Check IP addresses and connection pa-rameters in TM 1703 mic and
rameters in TM 1703 mic and the remotethe remote station
Operation and Maintenance TM 1703 mic
Operation and Maintenance TM 1703 mic 165165
DC6-013-2.01, Edition 08.2008 DC6-013-2.01, Edition 08.2008
027
027 No No internal internal modem modem supply supply possible possible Internal Internal modem modem supply supply not not possiblepossible •• Exchange power supply against versionExchange power supply against version
>= B or
>= B or
•
• Exchange CP-6020Exchange CP-6020 / /CP-6040 againstCP-6040 against version >= A
version >= A
Yes Yes Yes Yes *)*)
028
028 No No current current firmware firmware revision revision updateupdate Version of Version of WEBmicWEBmicwith that the parame-with that the parame-ters were generated is more current than ters were generated is more current than that of the firmware
that of the firmware
Carry
Carry out out a a firmware firmware update update Yes Yes NoNo *)*)
029
029 Modem Modem blockade blockade Substation Substation does does not not call call actively actively any any moremore •• Parameterize station in the master,Parameterize station in the master, otherwise the master sends a wrong otherwise the master sends a wrong password that the
password that the "unknown" station"unknown" station calls no more
calls no more
•
• Enter the password Enter the password correctly, consider correctly, consider upper case
upper case / /lower case letterslower case letters
Yes No
Yes No *)*)
030
030 Active Active disconnectdisconnect: : no no requestrequest TM 1703 mic did not detect a proper TM 1703 mic did not detect a proper connection release
connection release
Check DCD wiring of TM 1703 mic to Check DCD wiring of TM 1703 mic to modem
modem
Yes Yes Yes Yes *)*)
031
031 Passive Passive disconnectdisconnect: : open open circuitcircuit The connection was The connection was disconnectedisconnected incor-d incor-rectly (DCD signal is
rectly (DCD signal is "0" before command"0" before command
"hang up dial" has been received)
"hang up dial" has been received)
•
• Startup in the master during activeStartup in the master during active connection
connection
•
• Check telephone lineCheck telephone line
Yes Yes Yes Yes *)*)
032
032 Connection Connection setup setup not not possible possible Connection Connection to to master master not not possiblepossible •• Check telephone lineCheck telephone line
•
• Check telephone number Check telephone number
Yes No
Yes No *)*)
033
033 PLC PLC running running time time overflow overflow The processing time for the execution of The processing time for the execution of the application program has exceeded the application program has exceeded 50% of the set cycle time
50% of the set cycle time
•
• The system increases the cycle timeThe system increases the cycle time automatical
automatically by ly by 50% (max. 2 s 50% (max. 2 s possi- possi-ble)
ble)
•
• If PLC is stopped by the system, use aIf PLC is stopped by the system, use a smaller IL
smaller IL
Yes No
Yes No *)*)
034
034 PLC PLC checksum checksum error, error, PLC PLC haltedhalted Hardware error (the data in the memoryHardware error (the data in the memory range for the
range for the application program areapplication program are faulty)
faulty)
Rewrite
Rewrite the the IL IL to to the the SIM SIM card card I I Yes Yes NoNo
035
035 SIM SIM checksum checksum error, error, PLC PLC haltedhalted Hardware error (the data on Hardware error (the data on the SIM cardthe SIM card are faulty)
are faulty)
•
• Delete content of the SI card and re-Delete content of the SI card and re- write parameter
write parameters to the s to the SIM cardSIM card
•
• If no remedy: change SIM cardIf no remedy: change SIM card
I
I Yes Yes NoNo
036
036 PLC PLC syntax syntax error, error, PLC PLC haltedhalted An unknown ins An unknown instruction is truction is programmed programmed inin the IL
the IL
Check code and comments in the IL Check code and comments in the IL (syn-tax)
tax)
I
I Yes Yes NoNo
166
166 Operation and Maintenance TM 1703 micOperation and Maintenance TM 1703 mic
DC6-013-2.01, Edition 08.2008 DC6-013-2.01, Edition 08.2008 037
037 PLC PLC interval interval error, error, PLC PLC haltedhalted The cycle time for the The cycle time for the applicatioapplication programn program is to high
is to high
•
• Variable Variable PLC_CYCLETIPLC_CYCLETIMEME
•
• Processing time of the application pro-Processing time of the application pro-gram
gram
•
• Correct value of the variableCorrect value of the variable PLC_CYCLETIME (range 2 ms … 2 s) PLC_CYCLETIME (range 2 ms … 2 s)
•
• Processing time of the application pro-Processing time of the application pro-gram reaches 50% of the max. cycle gram reaches 50% of the max. cycle time
time
I
I Yes Yes NoNo
038
038 PLC PLC hw hw config config error, error, PLC PLC haltedhalted In the application programm a wrong typeIn the application programm a wrong type identification is used
identification is used
Check in parameterization and IL, the type Check in parameterization and IL, the type identification of data points used in the identification of data points used in the application program must match with the application program must match with the type in the
type in the parameterizatioparameterizationn
I
I Yes Yes NoNo
039
039 PLC PLC chr chr ring ring overflow overflow Number of state changes Number of state changes from informationfrom information items and integrated totals is greater than items and integrated totals is greater than the FIFO buffer chronological can store the FIFO buffer chronological can store
Yes Yes Yes Yes *)*)
040
040 PLC PLC chr chr global global ring ring overflow overflow Number of state changes from commands,Number of state changes from commands, setpoint values and counter
setpoint values and counter interrogationsinterrogations is greater than the
is greater than the FIFO buffer chronologi-FIFO buffer chronologi-cal global can store
cal global can store
Yes Yes Yes Yes *)*)
041
041 PLC PLC output output ring ring overflow overflow Too many telegrams generated by theToo many telegrams generated by the application program within one cycle application program within one cycle
Check
Check IL IL Yes Yes YesYes *)*)
042
042 PLC PLC c-stack c-stack underflow, underflow, PLC PLC haltedhalted In the IL a RET instruction is programmedIn the IL a RET instruction is programmed without CAL in
without CAL instructionstruction
Check IL (return to nesting level 0 not Check IL (return to nesting level 0 not possible)
possible)
I
I Yes Yes NoNo
043
043 PLC PLC c-stack c-stack overflow, overflow, PLC PLC haltedhalted Too many nesting levels by means of CALToo many nesting levels by means of CAL instructions
instructions
Check
Check IL IL (max. (max. 20 20 levels levels permittepermitted) d) I I Yes Yes NoNo
044
044 PLC PLC f-stack f-stack underflow, underflow, PLC PLC haltedhalted Too less transfer parameters for a functionToo less transfer parameters for a function or function block
or function block programmedprogrammed
Check
Check IL IL I I Yes Yes NoNo
045
045 PLC PLC f-stack f-stack overflow, overflow, PLC PLC haltedhalted Too many transfer parameters for a Too many transfer parameters for a func- func-tion or
tion or function block programmedfunction block programmed
Check
Check IL IL I I Yes Yes NoNo
046
046 Permanent Permanent looploop •• Internal errorsInternal errors
•
• Too many startups in Too many startups in successionsuccession
•
• Endless loop in the application programEndless loop in the application program
•
• Check ILCheck IL
•
• Check power supplyCheck power supply
•
• Please consult your Please consult your system supplier system supplier
No No
No No
047
047 NegatNegative ive confconfirmairmation tion OLA-OLA-commcommandand BehavBehaviout iout accacc. . to to IEC IEC Yes Yes NoNo *)*) 048
048 Negative Negative termination termination OLA-commOLA-command and Behaviout Behaviout acc. acc. to to IEC IEC Yes Yes NoNo *)*) 049
049 Console Console system system disabeld disabeld by by firmware firmware Software Software error error Please Please consult consult your your system system supplier supplier Yes Yes NoNo 050
050 IOA IOA MTS_LAEUFT MTS_LAEUFT wrong wrong Yes Yes NoNo
Operation and Maintenance TM 1703 mic
Operation and Maintenance TM 1703 mic 167167
DC6-013-2.01, Edition 08.2008 DC6-013-2.01, Edition 08.2008
051
051 IOA IOA enabeling enabeling wrong, wrong, console console halted halted Yes Yes NoNo 052
057 Wrong Wrong telegram telegram received received (SK)(SK) Error with the conversion of the SK mes-Error with the conversion of the SK mes-sage to the IEC mesmes-sage
sage to the IEC message
Check parameters in the
Check parameters in the master, i.e.master, i.e.
with/without
with/without component component number, pnumber, pack- ack-age, regis-tered under Diagnosis | Diagnosis History tered under Diagnosis | Diagnosis History
Yes No
Yes No
059
059 SK SK addressinaddressing g fault: fault: IOA2 IOA2 must must be be 00 Must be "0" for measured values andMust be "0" for measured values and integrated totals
integrated totals
See
See error error 058 058 Yes Yes NoNo
060
060 SK SK addressinaddressing g fault: fault: IOA3 IOA3 must must be be 00 Not used, must be always "0" in theNot used, must be always "0" in the SK mode not be greater than 15
not be greater than 15
See
See error error 058 058 Yes Yes NoNo
062
062 SK SK addressing addressing fault: fault: IOA2 IOA2 odd odd (DP)(DP) Only even bit numbers can be used for Only even bit numbers can be used for double-point information items double-point information items
See
See error error 058 058 Yes Yes NoNo
063
063 SK addressing fault: IOA2 for SPSK addressing fault: IOA2 for SP used
used
IOA1
IOA1 must must be be definite definite over over all all formats formats See See error error 058 058 Yes Yes NoNo
064
064 SK addressing fault: IOA2 for SPSK addressing fault: IOA2 for SP used
used
See
See error error 063 063 See See error error 058 058 Yes Yes NoNo
065
065 SK SK acknowledgement acknowledgement error error Occurs only Occurs only with with PCBMxx PCBMxx Check Check quality quality of of line line Yes Yes NoNo 066
066 Permanent Permanent reset, reset, firmware firmware disableddisabled Too many startups performed within shortToo many startups performed within short time, TM 1703 mic has been switched off time, TM 1703 mic has been switched off and on too
and on too many times withinmany times within
•
• Check power supplyCheck power supply
•
• If error cannot be If error cannot be corrected, pleasecorrected, please consult your system supplier consult your system supplier
Yes No
Yes No
067
067 PLC PLC enabled enabled no no PLC PLC code code availableavailable The PLC function is released under The PLC function is released under PLC | Configuration, but no code PLC | Configuration, but no code loadedloaded
•
• Block PLC if not used or Block PLC if not used or
•
• Load PLC codeLoad PLC code
Yes No
Yes No
068
068 Wait/Wait/schedule schedule with with disable disable Internal Internal software software error error Please Please consult consult your your system system supplier supplier No No YesYes
168
168 Operation and Maintenance TM 1703 micOperation and Maintenance TM 1703 mic
DC6-013-2.01, Edition 08.2008 DC6-013-2.01, Edition 08.2008 069
069 TE-6420 TE-6420 IOA IOA is is not not singlepointsinglepoint The binary output is not The binary output is not set as single-pointset as single-point information for this IOA
information for this IOA
Yes No
Yes No
070
070 TE-6420 TE-6420 IOA IOA not not from from DO-62xxDO-62xx The output must be on a DO module andThe output must be on a DO module and not on the master control module not on the master control module
Yes No
Yes No
071
071 TE-6420 TE-6420 IOA IOA not not from from DI-61xx DI-61xx Reserved Reserved internally internally Yes Yes NoNo 072
072 TE-6420 TE-6420 IOA IOA is is not not FloatingpoinFloatingpointt The output of the AO is not set to float for The output of the AO is not set to float for this IOA
074 TE-6420 TE-6420 IOA IOA doubled doubled usedused Somewhere the same IOA was assignedSomewhere the same IOA was assigned for the TE-6420
for the TE-6420
Yes No
Yes No
075
075 TE-6420 TE-6420 only only 1 1 rotation rotation speed speed sup.sup. The speedmonitoring may be releasedThe speedmonitoring may be released only once per TM 1703 mic
only once per TM 1703 mic
Yes No
Yes No
076
076 TE-6420 TE-6420 IOA IOA unknownunknown The set IOA is not found on any relevantThe set IOA is not found on any relevant module
module
Yes No
Yes No