electric vehicle drive applications
Real-time Analysis of a Modified State Observer for Sensorless Induction Motor Drive used in Electric Vehicle Applications
... for a given speed command of 165 rad/s. Although, both reach the reference speed at almost identical time, the estimated speed oscillations are comparatively very high for SMLO1 as shown in Fig. 6(a) as compared to SMLO2 ...
22
Implementation of NI Labview based BLDC Motor Drive Controller for Electric Vehicle
... The rotor part of a brushless motor is often a permanent magnet synchronous motor, but can also be a switched reluctance motor, or induction motor. Brushless motors may be described as stepper motors; however, the term ...
6
Wireless Power Transfer for Electric Vehicle Applications
... It includes several stages to charge an EV wirelessly. First, the utility ac power is converted to a dc power source by an ac to dc converter with power factor correction.Then, the dc power is converted to a ...
6
An evaluation of silicon carbide unipolar technologies for electric vehicle drive trains
... control drive-trains has been explored in ...hybrid electric vehicle power-trains was investigated in [11], where it was seen that system efficiency as well as compactness was ...on-board ...
13
Comparison of Nth Harmonic Injection Technique with SPWM Technique for N-Phase VSI Fed N-Phase IM Drive
... several applications such as hybrid/electrical vehicles, ship propulsion, high power and aerospace applications, here a leg of the drive can be formed by using several solid state ...system ...
11
Optimization of outer rotor hybrid excitation FSM for in wheel direct drive electric vehicle
... Abstract—Research on flux switching machines (FSMs) has been an attractive topic recently due to tremendous advantages of robust rotor structure, high torque, and high power capability that suits for intense ...
6
Design and Comparison of Axial-Flux PM BLDC Motors for Direct Drive Electric Vehicles: Conventional or Similar Slot and Pole Combination
... direct-driven applications due to their high torque-density, high efficiency, and extreme compact ...simple vehicle model load is considered which includes rolling resistance, aerodynamic drag, and climbing ...
6
A Modern Design of Torque Ripples Reduction in BLDC Drive for Electric Vehicle Application
... There are two basic rotor designs surface permanent magnet rotor design and interior permanent magnet rotor design as shown in Figure 1. For the surface permanent magnet rotor design, the winding are located in the core ...
14
Solar PV-Powered Electric Vehicle With BLDC Drive For Adjustable Energy Management
... Abstract- Electric vehicles (EVs) offer a possible way out to reduce a emission of green ...on vehicle batteries can be reduced by using the Photovoltaic (PV) panels on the ...
6
Hybrid-electric vehicle design and applications
... References: SAE Papers 790162 800057 800058 8001 1 1 891658 A High Energy Tubular Batten/ for a 1800 kg Payload Electric Delivery Van System Design of the The Drive System Electric Test [r] ...
171
V2G Based Solar Electric Vehicle Drive Train
... (particularly electric vehicles (EV)), HVAC, white goodsand industrial because it does away with the mechanical commutator used in traditional motors, replacing it with an electronic device that improves the ...
9
Direct Torque Controlled Drive Train for Electric Vehicle
... spikes which cause increase on torque ripple of BLDC motor which is not suitable for in-wheel application. An adaptive fuzzy control scheme via parallel distributed compensation has been applied to control velocity of ...
5
Average Model for an Interleaved DC/DC Boost for Fuel Cell Electrical Vehicle
... ABSTRACT: The development of electric vehicle has provided new opportunities in the area of power electronic. In this paper, we purpose, model, and analyze an interleaved three-phase Boost converter. This ...
11
FIRING ANGLE CONTROL OF DUAL CONVERTER USING DSPIC 30F 6012A FOR SPEED CONTROL OF DC MOTOR
... The electric drive system is used in many industrial applications, robotics and home appliances because of their low cost, less complex control structure and wide range of speed and torque which ...
7
On the Experimental Analysis of Integral Sliding Modes for Yaw Rate and Sideslip Control of an Electric Vehicle with Multiple Motors
... passive vehicle reaches this condition for a steering wheel angle amplitude of 70 deg, while the active vehicle is still within the specified sideslip boundary with an amplitude of 150 deg, which shows the ...
14
Hybrid Vehicle Controlled by Combined Pedal Mechanism
... hybrid electric vehicle is a type of hybrid vehicle which combines a conventional internal combustion engine propulsion system with an electric propulsion ...Hybrid Electric ...
5
Index Terms - Hybrid electric vehicle, hybrid electric two
... hybrid vehicle the amount of electric power required is smaller compared to full hybrid ...a electric motor connected in parallel connection to a largely conventional electric power ...The ...
6
Electric superbike racing: the design and construction of a championship winning electric superbike
... same vehicle weight. When optimising the battery for any vehicle the temperature rise of the pack must also be respected as the weight and volume of a forced cooling system (as used on some cars) cannot be ...
5
Development of a Fuzzy Slip Control System for Electric Vehicles with In-wheel Motors
... the drive shaft, which reduces the weight and size of the system, but also requires that the speed-torque characteristics of the motors meet the requirements of the ...the vehicle model and are treated as ...
19
Application of Capital Asset Pricing Model in Indian Stock Market
... Doubly- Fed Induction Machines are used as motor as well as generators. Wound-rotor induction machines with stator and rotor connected to separate ac sources having different frequencies are said to be doubly- fed ...
5