Finite-element analyses
Realistic computable error bounds for three dimensional finite element analyses in linear elasticity
... analog of the Arnold, Douglas and Gupta element. We show that, if one wishes to avoid additional post-processing steps as in [18], then one is obliged to make use of so-called “macro-element” techniques and ...
29
Finite Element Analyses of Single-Edge Bend Specimens for J-R Curve Development
... Displacement-controlled loading was applied in all the models. For models with a/W ≥ 0.4, the displacement was increased from 0 to 1.5 mm through 5000 steps, whereas it was increased from 0 to 2 ~ 2.5 mm through 15,000 ...
129
Experimental and Finite Element Analyses of an I-Shaped Prototype for Different Orientations and Thicknesses
... ABSTRACT: Rapid Prototyping (RP) has been a powerful technology for preparing Prototypes of complex parts and products. In the present work, Fused Deposition Modelling concept of RP is used to prepare I-Shaped prototype ...
6
Placement induced effects on high tibial osteotomized construct biomechanical tests and finite element analyses
... special element density at the plate-screw junctions three times that of the remain- der of the model with an overall average element size of 2 ...three finite- element ...
10
Numerical Simulation Of Piping Vibrations Using Modal Correlation
... Finite element analyses were carried out using the ABAQUS [7] and FPIPE [8] finite element codes. These analyses were conducted as a MSc. The first FE analysis was carried out w[r] ...
8
Topology and shape optimization of gear casing using finite element and Taguchi based statistical analyses
... In order to validate the design during initial development stage, various iterations are carried out to bring an optimal one. Recent advances in commercial codes for producing optimal design has shortened the iterative ...
14
Effect of web holes on web crippling strength of cold-formed steel channel sections under end-one-flange loading condition - Part I: Tests and finite element analysis
... non-linear finite element analyses (FEA) are used to investigate the cases of both flanges fastened and flanges unfastened to the bearing plates, of circular web holes located centred above the ...
36
Cold-formed steel Back to Back Lipped Channel
... and finite element analyses are used to investigate the effect of such holes on web crippling under concentrated loading ...and finite element analyses was obtained. The ...
6
Original Article Simulated postoperative weight-bearing after fixation of a severe osteoporotic intertrochanteric fracture
... and finite element analyses to evaluate the stability of severe osteoporotic intertrochanteric fractures fixed with an Asian proximal femur intramedullary nail antirotation system ...the ...
11
Limit Load Analysis of Bolted Flange Connections
... Therefore, numerical Finite-Element analyses, performed according to a special code, e. g. KTA, must also fulfill the requirements of the code with respect to considered load cases, bolting ...
11
Experimental and Numerical Test for Buckling Characteristics of Spacer Grids in PWR Fuel Assembly
... The finite element analyses were performed to identify the effect of the number of rows and the number of columns on the buckling load of full size grid and small size gr[r] ...
8
Comparative Stress Analyses of Major RCPB Components by Using a Prototype of Integrated Finite Element Model
... and finite element analyses are carried out employing representative design ...previous finite element analyses by the authors for each major RCPB component; the vessel, ...
8
Development of Test Guidance for Compact Tension Fracture Toughness Specimens Containing Notches Instead of Fatigue Pre-Cracks
... 3D Finite Element Analyses to quantify the accuracy of formulae intended for pre-cracked specimens in fracture toughness testing standards ASTM E1820, BS7448-1 and ESIS P2-92 when applied to ...
10
Finite Element Analysis of Friction Stir Welding of Al2024 and 6063aluminium Alloy
... In the present study, the modeling of friction stir welding is carried out using thetransient finite element analyses. A moving heat source with a heat distributionsimulating the heat generated from ...
6
Modal analysis of Pneumatictwo Finger Robotic hand by Finite Element Analysis and Experimental Testing
... In order to confirm the stress and deflection which calculated through the theoretical analysis, the finite element analyses were performed on the flat beams of the robot hand. In this study three ...
9
Kathlyne_Bautista_-_Senior_Honors_Thesis.pdf
... 1. Finite element analyses are performed to study the effect of easily adjustable design parameters for this sonicator on the pressure distribution: (1) the height of the water in the tank and (2) ...
31
Ultimate Capacity of Expansion Bellows in a BWR Containment
... The paper describes the three-dimensional finite element analyses requested by Nuclenor and carried out by Principia, to evaluate the ultimate capacity of a vent [r] ...
6
Estimation of the Parameter Controlling Short-Term Creep Crack Growth under Combined Primary and Secondary Loading
... The finite element validation presented here using elastic-plastic-creep finite element analyses of single edged cracked plates subjected to combined primary tension and secondary ...
10
Shape Optimization of Pedestals Using Artificial Neural Network
... from finite element analyses, are used for training the neural ...predictions finite element analyses considering these data is carried ...
7
Custom designed orthopedic implants evaluated using finite element analysis of patient specific computed tomography data: femoral component case study
... calculation. Finite sliding was allowed and only overclosed nodes were ...The finite element analyses were solved using a blade server in the High Performance Computing Center at North ...
10