finite-element computer simulation
Computer Aided Design and Finite Element Simulation Consistency
... In the case of CAD model input, generating a conform model means that the topology of the polyhedral model must be identical to that of the initial B-Rep NURBS model as it is available in the STEP file. In other words, ...
16
Simulation of the static mechanical behaviour of a pressurized water reactor fuel assembly
... and computer simulation of static mechanical response of a PWR fuel assembly, with the help of the finite element code “CAST3M” [6] developed by ...of simulation showed a quite good ...
7
Finite element simulation of a rolling process of aluminium
... of computer simulation methods. Computer simulation has been used to optimize the rolling parameters that will be used during production since the advancement of ...using finite ...
24
Journal of Engineering Science and Technology Review 13 (5) (2020) Research Article
... through simulation is scarce, especially by simulating the process of drilling rock ...on computer or shortening the design ...breaking finite element model of personalized PDC bit with sting ...
10
ANALYSIS OF RCC BEAMS WITH WEB OPENING THROUGH EXPERIMENTAL, COMPUTER SIMULATION AND ANALYTICAL APPROACH
... method, finite element model was prepared in ANSYS software considering identical geometric and material properties that of casted ...beam. Computer simulation was carried out and detailed ...
7
Effects of Rayleigh Number on MHD Heat Transfer and Fluid Flow in Two Dimensional Open Square Cavity with Heat Generation
... Computer simulation of Finite Element Method is used to perform the analysis of laminar natural convection heat transfer and fluid flow in an open square cavity with a heated circular ...
16
Finite Element Simulation of Pressurized Fluid
... dynamic simulation of the landing and ...the computer models developed for this purpose, the shock absorber parameters are enhanced to maximize its efficiency and peak reaction ...
6
Finite Element Analysis and Simulation of A Magneto - Rheological Damper
... In COMSOL for designing a particular damper for magneto rheological fluids, viscosity has a minimum value and if it is attenuated, the simulation does not give satisfactory result. This is mainly due to the fact ...
8
Finite element simulation of the braiding process
... on computer simulations (Radi and Hami 2016; Salvendy ...the finite element (FE) method is also widely used to simulate manufacturing steps, and for the virtual pre- dictions of mechanical properties ...
11
Investigations on the Effects of Different Tool Edge Geometries in the Finite Element Simulation of Machining
... the computer technology, the finite element method (FEM) and numerical simulation have been increasingly used to study the machining ...The simulation results showed that an increasing ...
10
Finite Element Machining Simulation of AISI6150 Steel
... a finite element environment in order to perform a machining simulation to identify chip formation, cutting forces and temperature distribution in tool and ...of finite element ...
8
Dynamic Analysis on Tillage Equipment Used in Agriculture Using Ansys Software
... by Computer Aided Engineering Analysis by Gopal ...of Computer Aided Engineering (CAE)- Techniques by finite element and simulation methods are done in CAD-Analysis software for the ...
8
Simulation of Pipe Hydroforming
... the finite element method can be applied to any material model, any boundary condition, and any structural ...the finite element method. Secondly, the finite element method can ...
80
A Survey On Physical Methods For Deformation Modeling
... The simulation of deformable objects is essential for many ...example, computer aided design uses deformable models to simulate the deformation of industrial ...the simulation of ...realistic ...
6
DYNAMIC ANALYSIS AND STRUCTURAL DESIGN OF TURBO GENERATOR FRAME FOUNDATION – A REVIEW
... Peter Nawrotzki [4] presents a systematic overview of the static analysis and dynamic analysis of turbine reinforced concrete foundations and also focuses on the load cases to be applied for foundation. Peter Nawrotzki ...
6
A New Damage Model to Predict Orthotropic Nonlinear Behavior of Woven Glass-Epoxy Composite
... that the damage modes in the fiber and shear directions were decoupled [5]. Mi et al. described a progressive failure criterion for the mixed-mode delamination of fiber reinforced composites, based on the cohesive ...
6
An isogeometric continuum shell element for non-linear analysis
... shell element is characterized by the absence of rotational degrees of freedom, which is convenient when stacking them, yet possesses shell kinematics, and is rather insensitive to shear locking and membrane ...
18
Finite element simulation of Durelli's photoelastic stress minimization method for shape optimization
... (1999), Optimal hole profile in a finite plate under uniaxial stress by finite element simulation of Durelli's photoelastic stress minimization method", Finite Elements in Analysis[r] ...
166
Characterization and Modeling of the Mechanical Behavior of Aeronautical Alloy Based Composite
... by finite element method and experimental test. The numerical finite element simulation allowed us to understand and manage a number of phenomena encountered during the mechanical ...
10
Finite Element Analysis based Simulation of Friction Process
... based simulation to find heat generated during frictional ...with finite element analysis ...friction simulation model without the need of complex computational power or knowledge of precise ...
5