liquid jet
Removal Efficiency in Industrial Scale Liquid Jet Ejector for Chlorine - Aqueous Caustic Soda System
... nozzle liquid jet ejector which is one type of venturi scrubber. Liquid jet ejectors are those which are using a mechanical pump to generate a high velocity fluid ...fluid jet creates ...
10
Prediction of the Occurrence of Swirling Liquid Jet
... the surface of a bath agitated by a liquid jet is also oscillated by impingement of the jet. The rotary sloshing takes place when the aspect ratio is greater than approximately 0.2. Therefore, the ...
5
A thermal hydraulic comparison of liquid microchannel and impinging liquid jet array heat sinks for high power electronics cooling
... forced liquid cooling strategies that show considerable promise for the cooling of high heat flux electronic devices are microchannel and impinging jet heat ...sinks. Liquid jet impingement is ...
11
Heat Transfer Analysis in Automotive Exhaust System using Liquid Jet Cooling
... in liquid coolant velocity in liquid jet cooling device enhanced the heat transfer between exhaust pipe and cooling ...in liquid flow ...of liquid jet cooling device lower the ...
7
A Novel Needleless Liquid Jet injection Methodology for Improving Direct Cardiac Gene Delivery: An Optimization of Parameters, Aav Mediated Therapy and investigation of Host Responses in Ischemic Heart Failure
... novel liquid jet device approach (2) Compare the new method against traditional IM injection with two different vector constructions and evaluate outcome (3) Evaluate the host response resulting from both ...
197
A REVIEW ON COOLING OF DISCRETE HEATED MODULES USING LIQUID JET IMPINGEMENT
... components. The type of working fluids (Water / Fluorocarbon liquids / Dielectric fluids / Nanofluids) used for cooling, mode of heat transfer (Natural / Forced / Mixed) from electronic components, and the method of ...
13
Heat Transfer Enhancement through Liquid Jet Impingement
... stagnation jet area and the associated entrainment of the heated liquid from the ...single jet impingement using SiO2-water nanofluids with various volume fractions (1%, 2% and ...confined jet ...
5
Nozzle Geometry Effects in Liquid Jet Array Impingement
... impinging liquid jets in electronics thermal management is attracting some consideration due to their very high heat transfer coefficients, hot spot targeting capabilities and moderate hydraulic power ...water ...
46
Experimental Evidence of Capillary Interruption of a Liquid Jet
... ( ∂ ∂ ∂ ∂ A l )( l V ) = A V = 2 r and ( ∂ ∂ A r )( ∂ ∂ r V ) = 1 r , where 2 r is due to formation of a fluid-air inter- face and 1 r due to its curvature. The physical meaning of these two effects can be clarified by ...
7
Continuous Reaction Crystallization of Struvite in a DTM Type Crystallizer With Jet Pump of Ascending Suspension Flow in a Mixing Chamber–Kinetic Approach of the Process
... Experimental results concerning reaction crystalliza- tion of struvite from diluted water solutions of phos- phate(V) ions in a continuous DTM type crystallizer with internal circulation of suspension driven by ...
9
The crystallization processes in the aluminum particles production technology
... the liquid jet stability indicate, that its decomposition occurs with the formation of polydisperse aerosol in the immediate vicinity of the outlet to working ...
7
Prediction of the Occurrence of Swirl Motion at Interface between Stratified Two Liquids
... by eq. (1). The physical properties of liquids (kinematic viscosity and density) did not affect the boundary. The interfacial tension between two liquids was approximately 55 mN/m in every case. Effect of the interfacial ...
7
Biological Sulphate Reduction with Hydrogen in a Jet Loop Biofilm Reactor
... sulphidogenic jet loop biofilm reactor using hydrogen as electron ...this jet loop reactor, high mass transfer rate between hydrogen and sulphate reducing active biomass is achieved by using a liquid ...
12
Liquid Breakup and Atomization of Pressure Jet and Swirl Atomizers.
... a liquid jet can be classified into distinct regimes of ...the jet depending upon the operating ...the jet, leading to its breakup, and it is important that these forces can be identified in ...
208
Generation of biomaterial particles with controlled dimensions via electrospraying
... the liquid surface due to instabilities brought on by the intense electric field at the ...mechanism, liquid is ejected via the formation of liquid jet which breaks into droplets after some ...
8
Fluid Dynamics Simulation of High Speed Jet under Distinct Initial Input Velocities
... [8] Gong, J., Xia, W., Li, J.H. and Wei, X.Y. (2017) Computational Fluid Dynamics Si- mulation of High Speed Jet under Different Input Pressures. International Journal of High Energy Physics , 4, 12-18. ...
7
COMPARISON OF BOG TREATMENT TECHNOLOGY IN LNG STATION WITHOUT LNG OUTPUT
... in jet refrigeration recovery; (3) Systematic optimization of equipment energy consumption by mathematical model (4) Develop new technologies to make up for the shortcomings of previous ...
5
A Versatile Liquid-Jet/Sessile Droplet System for Operando Studies of Reactions in Liquid Dispersions and Solutions by X-ray Absorption Spectroscopy
... Recycling liquid-jet configuration. In the recycling liquid- jet configuration, the sample was continuously pumped through the cell (up to 370 mL min −1 ) and recycled back to a glass reactor ...
10
A Computational Analysis of Gas Jet Flow Effects on Liquid Aspiration in the Collison Nebulizer
... Aerosol Jet® inks would require a Δ P > 18000 Pa on top of the hydrostatic pressure (about 400 Pa), which does not seem possible with a gas flow rate Q < 2000 sccm (in view of Table ...in jet ...
8
A Computational Analysis of Gas Jet Flow Effects on Liquid Aspiration in the Collison Nebulizer
... gas jet to syphon liquid into the jet stream, then to blow and shear into liquid sheets, filaments, and eventually ...the liquid aspiration mechanism among other aspects of the Collison ...
8