longitudinal direction
REGARDING STABILITY ANALYSIS OF THE VIBRATION MOVEMENT OF THE SPINDLE IN LONGITUDINAL DIRECTION AT CNC LATHE
... The paper presents a stability analysis of CNC lathe processing using Nyquist criteria starting from the vibrations in the longitudinal direction on a model of the main shaft of the CNC machine. The model ...
7
ESTABLISHING THE EQUATIONS THAT DETERMINE THE VIBRATION MOVEMENT OF THE SPINDLE IN LONGITUDINAL DIRECTION AT CNC LATHE
... The paper presents a mathematical model for analysis of vibration movements in case of CNC lathes. It is a known fact that vibrations represent an important component in determining the precision of a CNC machine. The ...
6
Microstructures of 50 nm Cu Interconnects along the Longitudinal Direction
... the longitudinal direction of Cu interconnects of less than 100 ...the longitudinal direction is very ...the longitudinal direction using focused ion beam (FIB) ...
5
Seismic Analysis of Subsea Cable in Longitudinal Direction
... the longitudinal displacement profile is developed from spatially variable ground motion time ...The longitudinal displacement profile is used to perform a series of three dimensional finite element ...
8
Distribution of pollutant in longitudinal direction of open channel flow
... Therefore, this study is going to determine how the type of contaminated substances, velocity of flow, type of flow, bed slop of channel, and other factors can affect on distr[r] ...
22
PUSHOVER ANALYSIS AN INELASTIC STATIC ANALYSIS METHOD
... Organized by C.O.E.T, Akola & IWWA, Amravati Center. Available Online at www.ijpret.com 486 1. Conservative results are obtained from the Displacement coefficient method in the longitudinal direction of ...
8
Inhomogeneous Hardness Distribution of High Pressure Torsion Processed IF Steel Disks
... the longitudinal direction (namely LD position) and transversal direction (namely TD ...radius direction on the axisymmetrical section plane of HPT ...
6
Mechanical and Microstructural Characteristics of the Fiber-Reinforced Composite Materials
... transverse direction to roughly 530 MPa in the longitudinal ...the longitudinal direction (AA) had much more of a volume fraction occupied from fibers and therefore made the material stronger ...
13
Mechanism of Pipe End Deformation after Cutting of Square Steel Pipe Formed by Roll Forming
... a longitudinal direction to generate a model that has uniform sectional shape in the longitudinal direction; (3) Remove boundary condition at both ends to allow deformation at the cutting ...
6
3D Printing of Continuous Carbon Fibre Reinforced Thermo Plastic (CFRTP) Tensile Test Specimens
... in printing carbon fibre reinforced thermoplastic (CFRTP) tensile test specimens according to the JIS K 7073 by making use of fused deposition modelling. Several different types of CFRTP tensile test specimens are ...
10
Measurement Uncertainty Assessment in Remote Object Geolocation
... as longitudinal and lateral the direction of the rangefinder laser beam and its orthogonal, ...lateral direction, while the one in longitudinal direction remains virtually constant for ...
9
A MILP Model to Select Cutting Machines and Cutting Patterns to Minimize Paper Loss
... the longitudinal direction occurs if the width of a cutting pattern is less than the width of a master roll, and the trim loss in the transversal direction occurs if the required lengths of products ...
6
Mechanical properties investigation of monolayer h BN sheet under in plane shear displacement using molecular dynamics simulations
... the longitudinal shape of a wrinkle, the amplitudes of a number of profiles of the sheethave been measured at the following distance from the bottom fixed edge, ...positive direction is parallel to the ...
24
Development and verification of a 9-DOF armored vehicle model in the lateral and longitudinal directions
... and longitudinal dynamic [20, 25] of the vehicle ...the longitudinal direction to body flexibility are also considered in developing the 9 DOF vehicle ...and longitudinal forces and also ...
21
Assessment and Retrofit of the Bridge over Kouris River, Cyprus
... DOI: 10.4236/ojce.2017.73023 347 Open Journal of Civil Engineering strengthening only the existing part of the deck without any interventions/ strengthening on the existing piers. The bridge deck was widened by ...
13
Local Reinforcement of 6061 Aluminum Alloy Bar Using High Frequency Induction Heating Apparatus
... radiation thermometer was set to 0.78 to accurately measure the temperature. The radiation thermometer measured the temperature at the tip of the bar. The tip of the bar was locally heated for the solution treatment ...
7
Seismic Response Of Multi-Storied Steel Building By Using Steel Plate Shear Wall And Steel Braced System
... in longitudinal direction but it is relatively lesser in transverse direction about 17% and it is higher for all other models in both the longitudinal as well as transverse ...
7
Seismic Upgrading of the Turbine Hall And Electric Building Of Unit 5/6 KOZLODUY NPP
... • The main part of the upgrading work will be done from outside (row G) and the technological process will not be disturbed. • The stiffness in longitudinal direction will be incr[r] ...
8
Compressive deformation of wood impregnated with low molecular weight phenol formaldehyde (PF) resin IV: Species dependency
... As the mechanical properties of PF resin-impregnated wood improving linearly with density for Japanese cedar, 6 Young’s modulus and bending strength in the longitudinal direction were compared between ...
5
Generating and measuring the anisotropic elastic behaviour of Co thin films with oriented surface nano strings on micro cantilevers
... This designed, homemade device allowed the inci- dence plane of the plasma to be parallel or perpendicu- lar to the longitudinal direction of each MCL. Therefore, the nano-strings generated in the ...
7