Sensitivity analysis for Electron Beam Melting model
In-situ Electron Imaging for the Electron Beam Melting Process.
... of electron optics, comes with an entire new way of studying the melt pool condition of the EBM ...incoming beam encounters the powder material before it reaches the build ...incident electron, where ...
118
Additive Manufacturing of Tungsten via Selective Laser Melting and Electron Beam Melting
... The geometry response was significantly affected by the variables speed and current. A second order model fitted the data well but with an R 2 (pred) value of 57.1% can not be used as a reliable predictor. Within ...
211
Metallurgy of additive manufacturing: Examples from electron beam melting
... 72 ∼1375 fcc 8.3 212 Nb ∼50 ∼2495 bcc 8.4 105 Fe 19 1537 bcc 7.9 120 system. Appropriate sizes of cylindrical components were fab- ricated in order to make tensile specimens for uniaxial tensile testing at a nominal ...
14
A Quantitative Evaluation of Electron Beam Sensitivity in Calcite Nanoparticles
... its sensitivity under electron irradiation in both conventional and scanning TEM damaging through its radiolytic decomposition to calcium ...a model material to compare damage under different ...
5
Thermal near infrared monitoring system for electron beam melting with emissivity tracking
... This makes it ideal for in process monitoring of AM systems like EBM. Also described was the implementation of our melt pool tracking and our corollary process of emissivity correction, which is an important step towards ...
6
Electron Beam Melting of Advanced Materials and Structures, mass customization, mass personalization
... consistently model the build up and remelting of subsequent ...the model in a subsequent layer would involve remeshing the added mass of powder without losing the temperature profiles generated during the ...
219
Thermal Modeling and Simulation of Electron Beam Melting for Rapid Prototyping on Ti6Al4V Alloys.
... element analysis package called COMSOL ...(electron beam) and the powder bed were developed using a step- by-step approximation ...proposed model strategy by setting up a controlled ...
250
Surface Roughness of Electron Beam Melting TI-6AL-4V Effect on Ultrasonic Testing
... EBM has grown in popularity since its commercialization in 2001. The PBF technique behind EBM provides support of the component during manufacture. This support comes from the unmelted powder which remains on the build ...
128
X-ray Tomography Characterisation of Lattice Structures Processed by Selective Electron Beam Melting
... to melting and solidification may not be the same when melting material on top of layers of loose particles as it is when laying down on previously melted ...Further analysis was carried out, ...
13
Microstructure of the Nickel-Base Superalloy CMSX-4 Fabricated by Selective Electron Beam Melting
... Powder bed-based additive manufacturing (AM) processes are characterized by very high- temperature gradients and solidification rates. These conditions lead to microstructures orders of magnitude smaller than in ...
12
Microstructure and mechanical properties of a high Nb-TiAl alloy fabricated by electron beam melting
... individual electron beam scanning ...our model simulation. As shown in Fig. 3, when the focused electron beam was scanned close to the measured point of in- terest, the temperature ...
14
Tailoring the thermal conductivity of the powder bed in Electron Beam Melting (EBM) Additive Manufacturing
... thermal model to approximate how much energy input is required during preheating and melting phases to maintain the temperature of the current layer and ensure the powder bed is adequately ...his ...
9
X-ray tomography characterisation of lattice structures processed by Selective Electron Beam Melting
... to melting and solidification may not be the same when melting material on top of layers of loose particles as it is when laying down on previously melted ...Further analysis was carried out, ...
12
Effect of Melt Scan Rate on Microstructure and Macrostructure for Electron Beam Melting of Ti 6Al 4V
... Figure 2. Isometric CAD model representing vertical (V) and horizontal (H) build orientations. The build direction is represented by arrow denoted B. and etched with a Kroll reagent consisting of 0.1 L water, 5 mL ...
6
The Effectiveness of Hot Isostatic Pressing for Closing Porosity in Titanium Parts Manufactured by Selective Electron Beam Melting
... However, the large tunnel defects, which could appear as separated segments in the 3D visualizations of the XCT data due to the small size of the ligaments connecting them, were found to persist in some samples following ...
8
The electropolishing of electron beam melting, additively manufactured TI6AL4V titanium : relevance, process parameters and surface finish.
... I would like to firstly thank Dr. Li Yang as my thesis advisor, prime mentor, and motivator throughout this work. His strong passion and interest in science and engineering as well as his positive spirit are an ...
94
Pilot Feedback Electronic Imaging at Elevated Temperatures and its Potential for In-Process Electron Beam Melting Monitoring
... Q analysis was carried out on both raw and processed electronic images to evaluate the influence of temperature on image ...to electron beam ...the electron beam during heating is ...
34
A study on the mechanical properties of micro-truss Ti-6Al-4V materials fabricated by Electron Beam Melting
... 2 3 1 0.97 ± 0.023 0.88 ± 0.252 0.08 0.079 ± 0.004 3 9 1.5 1.48 ± 0.019 1.35 ± 0.223 0.17 0.158 ± 0.002 4 3 1.8 1.78 ± 0.028 1.65 ± 0.216 0.23 0.216 ± 0.005 mismatch in strut dimensions can be observed in the deviation ...
148
Evaluation of Ti-6Al-4V Parts Produced with Rapid Prototyping Technology: Electron Beam Melting Machine
... of beam current, beam speed and offset ...a model equation was established in order to relate EBM’s process parameters to measured properties of surface roughness, CPT, density and ...than ...
134
γ-Titanium Aluminide Alloys for Aircraft and Automotive Engine Components Applications Processed by Electron Beam Melting
... conclusion, analysis performed on powders in different recycling condition and used for several EBM cycles confirm that, for what concerns particle size distribution, flowability and apparent density, the adopted ...
335