Stem cutting
The effect of leaf presence on the rooting of stem cutting of bitter melon and on changes in polyamine levels
... of stem cuttings in different species ...melon stem cutting, as shown in other species, is sup- ported by the fact that the putrescine levels did not in- crease in defoliated cuttings that did not ...
5
Exploring sprouting and growth response of ixora stem cuttings (ixora cocccinea)
... that cutting length; node position, leaf number attached and leaf area were significant factor affecting the root ...per cutting than rest of the ...of cutting was significantly affected by the ...
6
Sensor based definition of buxus stem shearing behavior in impact cutting process
... to stem cutting, are necessary to design and fabrication of proper trimmer ...plants stem like barley, wheat, alfalfa, forge crops, safflower, sunflower and ...
8
Analysis of the strength properties of pea stems
... with stem strength at internode ...in stem diameter, of ap- proximately 50% between internode 2-3 and internode 8-9, accounts for much of the lodging behaviour of this ...initial stem failure ...
9
Vegetative propagation in Jatropha curcas L.
... The present paper reports improved technology for vegetative propagation of mature elite Jatropha curcas is highly desirable. Keeping this in mind, an attempt was made to standardize the technique of its vegetative ...
5
Determination of some constant parameters during cutting of canola stem
... stalk cutting, and reported that with increasing humidity, cutting energy increased and with increasing altitude, cutting energy decreased (Azadbakht et ...saffron stem and reported that ...
9
Quasi-static and impact cutting behavior definition of privet stem
... impact cutting process, a cutting tester similar Izod tester for metals, was ...arm, cutting blade and data acquisition system. The cutting blade with sharpened angel of 23 degree, rake angle ...
11
Vegetative propagation in Karanja (Pongamia pinnata L.)
... Study on vegetative propagation in Karanja (Pongamia pinnata) indicates the response of different treatments is respect to sprouting (%), rooting (%) and root length (Table 1,2 and 3). Generally, sprouting was initiated ...
5
Effects of blade sliding cutting angle and stem level on cutting energy of rice stems
... and cutting apparatus (Figure ...four cutting blades with different sliding cutting angles (Figure ...the stem smashing, the blade can cut stem without supported blade under the action ...
7
Responses of ornamental Mussaenda species stem cuttings to varying concentrations of naphthalene acetic acid phytohormone application
... by stem cutting taking from hard woods, semi-hard woods and sometimes from soft woods rooted in a rooting media under optimum nursery conditions; although some species/cultivars of potential aesthetic value ...
5
Parametric Effects and Optimization of Machining Parameters in Hard Turning: A Literature Review
... the cutting speed and the interaction effect of feed rate with nose radius of ...The cutting speed and the tool corner radius affected surface roughness ...as cutting forces and surface roughness ...
9
DESIGN OF MECHANICAL TEF HARVESTING MACHINE
... tef stem must be known. The cutting force for tef stems was measured by designing and fabricating a static and dynamic shear test apparatus and cutting force, cutting energy and power have ...
9
INFLUENCE OF SELECTED CUTTING CONDITIONS ON CUTTING FORCES
... of cutting wedge shape (ge- ometry), chip formation, as well as cutting condi- tions (cutting speed in this case) on cutting forces and respective components of cutting ...of ...
7
Intelligent design and simulation of roadheader cutting head
... FOR CUTTING HEAD OF ROADHEADER Cutting head has greater impact loads in the work process and the forces of each cutting pick are different, so it will lead to weak pick failure when it reaches the ...
7
ABSTRACT: In order to improve the cutting temperature in the cutting process, adverse effects of the cutting
... the cutting temperature in the cutting process, adverse effects of the cutting tool and the workpiece, it is better to join the cooling factors in the cutting to achieve a better ...
5
Investigations of Ultrasonic Vibration cutting of Ti-6Al-4V (TC4)
... traditional cutting process the UV cutting has shown its promising advantages in increasing tool life ,improving surface finish,reducing cutting forces and enhancing machining ...the cutting ...
5
Download Download PDF
... Access to lubricants is essential to any modern society and not only does lubrication reduce friction and wear by interposition of a thin liquid film between moving surfaces of various machinery/equipment or during ...
7
Study And Analysis Of GFRP Machining Using Alumina Based Cutting Tools
... alumina cutting tools. The machining process was performed at different cutting speeds at constant feed rate and depth of ...alumina cutting toll was evaluated by measuring the flank wear and surface ...
9
Complex Background Image Detection and Processing Based on Machine Vision
... The following number of "PU" or "PD" is the two-dimensional coordinate information that is passed or stayed by the knife. From a "PU" beginning with several "PD" until the next one is not ...
8
Analysis and experiment on cutting performances of high-stubble maize stalks
... the cutting speed is 9.5 m/s, the cutting angle is ...maximum cutting resistance and cutting power consumption are ...conventional cutting blade parameter, the maximum cutting ...
13