[PDF] Top 20 AppleShare Client 3.8 User’s Manual

... Note: If the server and client are not on the same AppleTalk network, the server may not appear in the “Select a file server” list. To connect to the server, click the Server IP Address button and enter the ... See full document

... To use AppleShare Client 3.8 you need to upgrade your system software to version 7.6 or later and configure your AppleTalk and TCP/IP control panels. Contact your server administrator for information about ... See full document

... 1 Open the Chooser and select the AppleShare icon in the upper-left corner of the window. If your network is divided into zones, they are listed in the lower-left corner of the window. When you select a zone, any ... See full document

... 1 The chart shows all grandMA consoles with names and IP-Addresses, that are available in this network. The column UNIV provides information for each console, if there are 4 or 8 DMX-outputs available on the ... See full document

... When the DVR receives a camera control command, it transmits that command up the coaxial cable to the PTZ device. RS485 is a single-direction protocol; the PTZ device can’t return any data to the unit. To enable the ... See full document

... Daily reports have three (3) report interval options: 15 minutes, half hour and hour. Daily reports are used to monitor the operations of a customer interaction center on a daily basis. The load activity data from ... See full document

... camera 3 of site B in the default window 2, just click the appropriate default window when you want to check the images, don’t need to modify the configuration of the ...support 8 different ... See full document

... FTP ENCODE If your FTP client or operating system does not support Unicode (e.g. Windows® 95/98/ME or MAC OS9/8), select the same encoding as your OS here in order to properly view the files and directories ... See full document

... There are 4 submenu settings within the MMS/GPRS function. They are Send Mode, MMS Set, GPRS Set and Send to. Send Mode means to choose a way to send MMS (refer to 4.1 table). MMS Set and GPRS Set means to have the right ... See full document

... 4 Choose the User/Group and Everyone privileges you want from the Privilege pop-up menus. For more information about the items in the sharing window, choose Show Balloons from the Finder’s Help menu and point to ... See full document

... Connect the serial port of your PC and that of EZL-200F, using the supplied serial communication cable. Then, run serial communication program such as Hyper Terminal and Teraterm. When the program is run, select the same ... See full document

... Sollae Systems Co., Ltd. - 31 - http://www.sollae.co.kr be temporarily saved in the buffer. Then, when there is no incoming data during the designated [Data Frame], CSE-H21 will send the saved data. If the [Data Frame] ... See full document

... Modbus/TCP protocol is used to communicate with CIE-M10‟s I/O ports. When CIE-M10 is in Slave/Passive mode, it operates as a standard Modbus/TCP device. It can be operated as a master. A master outputs data after ... See full document

... 2. Adjust the volume in the earpiece by moving the VOL slide control. With the amplifier on, incoming volume will be up to 43 dB louder. In standard use, the amplifier turns off whenever you hang up the telephone. This ... See full document

... the user to automatically set the IP address, subnet mask, gateway, and name server of ...the user to check [DHCP] item on ezConfig. Note that the user may have to check [ARP] item according to the ... See full document

... WPA is a security standard for users of devices equipped with Wi-Fi wireless connection. It is an improvement on and is expected to replace the original Wi-Fi security standard, Wired Equivalent Privacy (WEP). There are ... See full document

... The product model number is included on the package and the front of the manual. The serial number is located on the product unit. Please record the product model number and serial number in the spaces provided ... See full document

... 1. The Broadcast Search function is used to locate all AWK APs and WAC controllers that are connected to the same LAN as your computer. After locating a WAC-1001, you will be able to change its IP address. Since the ... See full document

... In case there is no recorded file, the message will show ‘No File’. In case the file has not sent to Service Server yet, the message “Uploading” will be shown. If Video and Audio has been downloaded in “Download” of ... See full document

... It is important to test this unit every week to make sure it is working prop- erly. Using the test button is the recommended way to test this Smoke Alarm. Press and hold the test button on the cover of the unit until the ... See full document