[PDF] Top 20 Bond strength between silorane-based composite resin and dentin substrate

... restorative! composite!resin!with!methacrylate!matrix!lead! to! its! acceptation! as! restorative! material! for! ...the! bond! system,! such! as! pulpal! damage, 2,3 ! and! ... See full document

... of silorane-based composite resins is approximately 1% ...addition, silorane exhibits the greatest stability in presence of visible light, along with optimal mechanical properties compared to ... See full document

... lorane-based composite resin to ...shear bond strength of silorane-based composite resin (Filtek LS) to RMGI versus Z250/Adper Scotch Bond ...the ... See full document

... flowable composite (Vertise, Kerr, Italy) was used in group ...the dentin surface and rubbed with moderate pressure using a microbrush for 15 to 20 ...cycles between 5-55°C in a thermocycler (TC-300; ... See full document

... In resin composite, SBU resulted in similar bond strength when compared to the positive control ...repair resin composite restora- tions – application of silane and ...highest ... See full document

... for bond strength (MPa) were: G1: ...the bond strength was statistically significantly higher for G1 and G3, which were not statistically significantly different between ...higher ... See full document

... The bond strengths to lased tooth substrates reported in the literature are often confusing and even contradictory ...higher bond strengths to laser-conditioned dentine than to acid etched dentine [2], ... See full document

... of resin composite may be a strong harmful factor in the survival of direct restorations, with the result of stress being transferred to the bond interface ...the bond interface, the C factor ... See full document

... (Single Bond 2) and two self-etch bonding systems to assess the push-out bond strength of composite resin posts to intracanal dentin of primary anterior teeth and reported that ... See full document

... to composite resin luting cements using various surface conditioning methods ...sufficient bond strength for composite ...failure between the framework and the luting cement has ... See full document

... improved bond strength to the tooth structure [6], as well as addressing the primary problem of reduced shear bond strength associated with provisional ...effective bond between ... See full document

... enhance bond strengths because water preserves the porosity of collagen network available for monomer inter-diffusion (Kanca, 1996; Perdigao et ...priming resin (Tay et ...Single Bond 2 ... See full document

... of dentin, an increase in wettability is expected because collagen removal produces a hydrophilic ...shear bond strength of single bond and silorane adhesive to dentin (p< ... See full document

... with resin composite (Filtek Z350, 3 M ESPE, ...the composite, the specimens were acid-etched with 37 % phosphoric acid for 30 s, rinsed with distilled water for 30 s, dried with compressed air for ... See full document

... passes, bond is created between the Calcium and Aluminum ions of the cement and the negative hydroxyl ions of hydroxyapatite crystals; it subsequently increases the cross-link density and compressive ... See full document

... SE Bond (Kuraray; Osaka, Japan) and Filtek Silorane System (Filtek; 3M/EPSE, USA) were used in this in vitro experimental ...SE Bond (Kuraray; Osaka, Japan) and Silorane System adhesive ... See full document

... reduced bond strength of bleached enamel has been related to the presence of residual free radicals due to the breakdown of hydrogen peroxide [14, 18] and alter- ations in the enamel composition and ... See full document

... superficial dentin surface was exposed on each tooth after wet grinding the buccal enamel with a diamond ...exposed dentin surfaces were further polished with wet #600-grit silicon carbide paper for 60 ... See full document

... The problem of post-operative sensitivity commonly presents to the restorative dentist as a transient pain that cannot be related to any other dental defect or pathology. It can be a result of number of factors such as ... See full document

... of silorane-based com- posites was much lower than other ...that silorane-based composite resins had relatively lower hardness compared with methacrylate-based compo- ... See full document