[PDF] Top 20 Effect of 2% Chlorhexidine on the Bond Strength of Direct Composite Restoration to Dentin: An in vitro Study

... demineralized dentin merely postpones rather than permanently arrest bond ...protective effect is still a question that requires further research. Chlorhexidine proved to be beneficial only ... See full document

... Luting agents are used to ensure the stability of fixed prosthesis throughout their serviceable lifespan. They can be interim luting agents or definitive luting agents. In doubtful situations, a prosthesis can be ... See full document

... smooth dentin surface with 600-grit sili- con carbide abrasive paper under constant water ...this study, a halogen light polymerizing unit (optilux501, sybronkerr, Danbury, ...600mW/cm 2 was used for ... See full document

... The self etching adhesives are alleged to be user-friendly (shorter application time with fewer steps) and less technique-sensitive (no wet-bonding, simple drying), thereby resulting in a reliable clinical performance, ... See full document

... with 2% chlorhexidine or 2% sodium bicarbonate did not have an immediate negative effect on the bond strength of the Clearfil SE Bond self-etch adhesive system to ... See full document

... resin composite or amalgam in areas of high ...in vitro experimental study to investigate the effect of four different conditioners on the shear bond strength of composite ... See full document

... and bond strength of a glass post to intraradicular dentin: comparison between microtensile and push- out ...Retentive strength of different intracanal posts in restorations of anterior ... See full document

... Deproteinizing enzymes such as collagenase and bromelain enzyme are newer techniques to remove collagen network [17]. Bromelain is a proteolytic en- zyme commercially obtained from the fruit or stem of pineapple. The ... See full document

... of dentin have undesirable effects on bonding ...the dentin surface and resin globules were found around the tubular orifices and on the surface of the hybrid layer(Tayet ...shear bond ... See full document

... e Bond and XP Bond) and two s elf -et ch adhesi ves (Prompt L -Pop and Xeno III) were emplo yed to bond the compos ...Shear bond st rengt h (S BS ) was determ ined aft er storage i n wat er ... See full document

... group study the using of the 3M universal bond (one bottle technique),this system represent the seven generation in bond classification which characterize by join acid etch, prime, and bond ... See full document

... of 2% chlorhexidine showed inferior bond strength when compared to the other ...that chlorhexidine digluconate has strong cationic properties, which may have reacted with the anionic ... See full document

... death. Chlorhexidine as a broad-spectrum MMP inhibitor, Hebling et ...that chlorhexidine was effective as an MMP inhibitor on total-etch adhesive, but did not show significant result on self-etch ...That ... See full document

... of bond strength to tooth surfaces. The micro- tensile bond strength test was used in most of the above mentioned ...micro-tensile bond strength measurements are relevantly ... See full document

... the effect of simplified ethanol-wet bonding on dentin bonding durability of etch and- rinse ...the dentin bonding durability of commercial hydrophilic etch-and-rinse adhesives and experimental ... See full document

... enhancing bond strength of flowable com- posites to fiber posts due to the ability of these compo- sites to penetrate into post surface irregularities which form semi-interpenetrating (semi-IPN) polymer ... See full document

... with composite resins, RMGICs self-adhere to hard tissue, thanks to the micromechanical interlocking of their ...to dentin is somewhat different; so that they attach to the dentin through a chelation ... See full document

... which chlorhexidine is ap- plied, some authors have used chlorhexidine after etch- ing and showed higher bond strength ...that chlorhexidine has been shown to inhibit enzyme activities ... See full document

... labial dentin surface was exposed by using a diamond bur (4138, KG Sorensen; Barueri, SP, Brazil) and a high-speed handpiece under water ...superficial dentin sur- face was polished by silicon carbide paper ... See full document

... durable bond to tooth structure ...less dentin demineralization compared to etch-and-rinse ...the bond to mineralized tooth structures, metal, and porcelain ...high bond strength of 10- ... See full document