Bonding Strength
Effect of Crystallization on the Bonding Strength and Failures of Plasma Sprayed Hydroxyapatite
... the bonding strength of the heat-treated HACs is further enhanced owing to the improvement of Young’s modulus and fracture toughness resulting from crystallization of the HA coating ...
8
Experimental Study on Bonding Strength of High Strength Concrete Subjected to Elevated Temperatures
... the bonding strength and cubes were used to obtain the compressive strength of ...High strength concrete is prepared by partial replacement of cement by silica fume; concrete mix is produced ...
7
Effect of Surface Coating on the Bonding Strength of Reinforcing Steel Bars in Concrete Structures
... the bonding strength between steel bars and the concrete is not well ...the bonding strength between polymer paint (local brand and other international one) coated bars and ...
7
Screw-nail withdrawal and bonding strength of paulownia (Paulownia tomentosa Steud.) wood
... withdrawal strength and bonding strength were investigated for pau- lownia (Paulownia tomentosa ...withdrawal strength was carried out according to the ASTM-D 143 and ASTM-D 1761 and Turkish ...
6
An Investigation on In-situ Strength and Bonding Strength of Polymer Modified Concretes (PMC) as Repair Overlays on Conventional Concrete Substrate
... proper bonding strength to substrate concrete, high tensile and flexural strength and low amount of shrinkage and ...The bonding strength of repair overlays to the substrate is also ...
12
Interfacial Reaction and Bonding Strength of Ti50Ni50 and Inconel 600 Dissimilar Brazed Joints
... for 180 s and 300 s were 387 MPa and 527 MPa, respective- ly. The unusual high shear strength of 527 MPa shown in Ta- ble 1 arose from the better formation of the fillet, shown in Fig. 3(b), which was caused by ...
5
Bonding strength of near surface mounted glass fibre reinforced polymer
... The performance of plain glass fibre reinforced polymer GFRP mounted at the outer tension surface of beams or known as near surface mounted NSM technique, with some bonded lengths and gr[r] ...
7
Bonding strength of multiple SiC die attachment prepared by sintering of Ag nanoparticles
... shear strength as shown in ...shear strength of low-pressure sintered Ag ...shear strength with increasing sintering pressure may be explained in terms of atomic diffusion and particle consolidation ...
10
Characteristics of Biomedical Beta Type Titanium Alloy Subjected to Coating
... tensile bonding strength of the coating layers. A bonding agent used in dental applications (orthomite super bond) was applied to the surface of the coating layer of each ...the bonding agent ...
7
Bonding Characteristics of Various Metals by DC Pulse Resistance Heat Pressure Welding
... state bonding by examining the mechanism of solid state bonding ranging from cold pressure welding to diffusion ...a bonding strength close to the strength of the parent metals, decrease ...
6
Evaluation of Bond Shear Strength of Heat Treated Cu Al Bonding Interface
... Cu-Al bonding interface. Generally, moderate IMC growth increases the bonding strength by alloying copper wires with aluminium ...the bonding interface brittle and act as a major cause for ...
8
Effect of surface protection associated to different bonding protocols on the bond strength to eroded dentin
... bond strength when compared to the other ...impaired bonding under some circumstances and the protocol for adhesive bonding resulted in some negative long-term bonding when the chlorhexidine ...
7
Ion-Doped Silicate Bioceramic Coating of Ti-Based Implant
... higher bonding strength than plasma-sprayed HA coating [22] ...higher bonding strength of CZS coating is attributed to the large content of zirconia in the CZS ...high strength and good ...
12
Metal Metal Bonding Process Using Cu+Ag Mixed Nanoparticles
... are seen for the joints bonded at different temperatures. At the bonding temperature of 160°C, the Cu+Ag mixed nano- particles are still encapsulated by polymers. No obvious sintering occurs, which lead to the low ...
5
Properties of Particleboard Made from UF with Low-formaldehyde (E1) (TECHNICAL NOTE)
... internal bonding strength, and thickness swelling of Particleboard made from chips of different species – hircanian forest, Iran- with sprayed with UF-low formaldehyde resin for the core layer and the face ...
5
Adherence of Porcelain Veneered on Titanium with an Intermediate Plasma Sprayed Zirconia Layer
... from bonding strength test of both PT and PZT were glued together, cut cross-sectionally, then ground and polished to observe the images by SEM as ...
6
Effects of five additive materials on mechanical and dimensional properties of wood cement-bonded boards
... strands of flax straw have a relatively high strength. 9'24'27 The IB strength was obviously decreased due to the cross- bonding strength of fibers in the retted flax [r] ...
8
The Synthesis, Characterization, and Application of Polysaccharides-Based Additives to Increase the Dry Strength of Paper.
... inter-fiber bonding strength and STFI index were tested only for CNs-DTPA-Ch-treated pulp hand ...inter-fiber bonding strength and STFI index were increased ...dry strength additives ...
227
Improvement on the properties of gypsum particleboard by adding cement
... As indicated above, when GPB was produced by adding an appropriate amount of cement, the cement acted to in- crease the bonding strength of boards and to resist the [r] ...
5
Tensile Strength of Ti/Mg Alloys Dissimilar Bonding Material Fabricated by Spark Plasma Sintering
... on bonding strength of sample bonded at 400ºC for 1 hr under applying pressure of 40 ...MPa. Bonding strength of Ti/Mg alloys (ST) was higher compared to Ti/Mg alloys for all bonding ...
7