Comparison of results: analytical model, finite element
Turbine missile impact assessment – comparison of results from empirical formulae and finite element analysis
... a comparison of the results from empirical mathematical methods (ETC-C, R3 Impact Assessment Procedure and Forrestal penetration model) with nonlinear finite element analysis used to ...
10
Additive manufacturing of an oxide ceramic by laser beam melting-comparison between finite element simulation and experimental results
... developed finite element model for LBM of ceramic materials has been established through a comparison with experimental ...The model solves heat and mass transfers whilst accounting for ...
44
Assessment of the primary rotational stability of uncemented hip stems using an analytical model: Comparison with finite element analyses
... the analytical model predicts the same stability ranking as the FE simulations, except that RotaMIN and RotaLOW switched ...the results between the two least stable stems, RotaMIN and RotaLOW, and ...
9
Comparison of finite element results with photoelastic stress analysis around dental implants with different threads
... a model simi- lar to the studied structure is made in transparent material that has photoelastic ...This model is placed un- der loading of the work conditions, which results in a de- formation and ...
6
COMPARISON BETWEEN FINITE ELEMENT ANALYSIS AND ANALYTICAL SOLUTION FOR COMPOSITE BEAM.
... beneficial. Finite element analysis (FEA) is one of the important tool to predict failure of ...paper finite element analysis (FEA) of composite is done and results are check with ...
7
Comparison between grillage model and finite element model for analyzing bridge deck
... the finite element technique is developing so rapidly, the job of carrying out finite element computations is a full time occupation which cannot be carried out at the same time by the senior ...
12
A Comparison of Analytical and Finite Element Solutions for Laminar Flow Conditions Near Gaussian Constrictions
... 2.3 Fluent Setup The model setup in Fluent will be similar to Figure 2, except that the area below r = 0 will not be modeled. The geometry will be treated as a “symmetrical” 2-d geometry in spherical coordinates ...
44
Optimizing Dental Implant Model by Comparison of Three Dimensional Finite Element
... (3-D MODEL) To construct a three-dimensional (3-D) finite element model for the study is a important operation in ...qualitative results of one case with respect to another, a 2-D ...
9
Inductance Comparison of the Solenoidal Coil of Modular Toroidal Coils Using the Analytical and Finite Element Method
... the finite element method (FEM) is employed to obtain SC ...The results obtained using the FEM confirms the analytical and empirical ...the comparison of the behavior of SC inductance, ...
16
Seismic Analysis of Buried Structures in Frequency Domain: Comparison between Analytical and Finite Element Methods (K345)
... These results were obtained for 5 harmonic excitations at the control point for different ...the analytical solution the correspondent acceleration at the center of structure is ...
8
Buckling Analysis of Circular Shells for RDE Reactor Pressure Vessel by Finite Element Study and Analytical Model
... 4. RESULTS AND DISCUSSION The buckling analysis of circular shell for RDE reactor pressure vessel has been done by computer code ...the results for critical buckling are good matched with the computing ...
8
A micro finite-element model for soil behaviour
... any model or experimental analysis. The results presented here demonstrate that hetero- geneous force transfer networks can be characterised while accounting for the effect of contact topology, grain mor- ...
14
Head Gasket Finite Element Model Correlation
... for comparison in the following ...physical results of the Cold Clamping Pressures, they do greatly affect the total CPU time and amount of iterations needed for completion of the ...distribution ...
150
Interpreting finite element results for brittle materials in endodontic restorations
... The prevalent use of the VM criterion in previous works is probably due to the fact that this is the usual criterion in the majority of engineering calculations and, also for this reason, it is incorporated as the ...
16
Comparison of a finite difference and a mixed finite element formulation of the uniaxial perfectly matched layer
... The numerical model produces waves that propagate at incorrect speeds. The dependence of the velocity of propagation of the numerical sinusoidal waves on frequency is termed as dispersion, while the dependence of ...
44
Comparison of Finite Element Methods in Fusion Welding Processes—A Review
... However, despite these advantages, this type of connection method has some drawbacks, for example, residual stress and structural distortion, mainly due to the process thermal cycles. Structural distortion is one of the ...
19
A Stochastic Finite Element Model for the Dynamics of Globular Macromolecules
... experimental results. Such an analysis would allow for a quantitative comparison of the flexibilities of biomacromolecules, which explicitly takes the shape of the molecular enve- lope into ...
38
Finite element model of a tennis ball impact with a racket
... an analytical model of a tennis ball impacting on a flexible freely suspended racket, based on a spring damper ...same results were found when the model was applied to a freely suspended ...
291
Finite element model of a cricket ball impacting a bat
... 2 Results for the ball/plate impact. The model results correspond to Plate-tuned 2 in Table ...the results for the ball/bat ...in comparison to the ...ball model, however, ...
7
Stochastic Approximation Finite Element method: analytical formulas for multidimensional diffusion process
... • Results are extended in Theorem 2.8 and Corollary 2.9 considering multiquadratic finite elements. The proof of the error estimates of Theorems 2.1 and 2.5 are respectively given in Sections 3 and 4. ...
26