maximum von Mises stresses
Stress Distribution in Human Tibia Bones using Finite Element Analysis
... of maximum von Mises stresses found on tibia bones which were on the middle of posterior tibia and the proximal ...peak stresses on the proximal tibia due to the lack of relatively soft ...
13
INVESTIGATION OF STRESSES IN ARM TYPE ROTATING FLYWHEEL
... them, maximum tensile and bending stresses induced in the rim and tensile stresses induced in the arm under the action of centrifugal forces are the main causes of flywheel ...of stresses in ...
10
Built in reliability design of highly integrated solid state power switches with metal bump interconnects
... the maximum von Mises stresses and creep strain accumulations occur in the solder joints used to join bumps on IGBTs during a realistic mission profile, but occur in the solder joints used to ...
14
Finite Element Modeling of Shop Built Spherical Pressure Vessels
... investigates stresses developed in a shop built carbon steel spherical storage vessels using finite element ap- proach as the analytical ...corresponding maximum Von-mises stresses are ...
6
Effect of lordosis on adjacent levels after lumbar interbody fusion, before and after removal of the spinal fixator: a finite element analysis
... motion, maximum von Mises stresses at cephalic adjacent levels, and contact force on facet joints was investigated when the lumbar spine was implanted with an interbody cage to simulate 0° and ...
9
Comparison of Short and Standard Implants in the Posterior Mandible: A 3D Analysis Using Finite Element Method
... The maximum von Mises stresses for dental implants are shown in Table 2 and ...The von Mises stresses were concentrated in the neck of implants in all models ...the ...
7
Analysis of Stresses on Straw Walker Crankshaft of John Deere 995 Combine Harvester
... by Von Mises theory the amount of stresses on crankshaft axle and crank parts was obtained and by Ansys 11 software, the maximum stresses was obtained and safety factor was created ...
8
Maximum von Mises Stress in the Sliding Contact of Coated Bodies
... Competent design decisions for the optimum configuration of a coated contact require the prediction of the stress state developing in the coated body under contact load. Conventional methods of superposition of effects ...
12
Finite Element Analysis of Equivalent stress and Deformation of Cementless Hip Prothesis
... damage. Maximum Equivalent von Mises stresses developed in the neck of the hip prosthesis and maximum total deformation in the implant for static condition were ...
5
Effect of off axis cell orientation on mechanical properties in smooth muscle tissue
... of Von-mises stresses ob- tained indicate that the maximum shear stress values of tracheal smooth muscle increase with increasing values of shortening strain for each off-axis cell ...
8
The Effects of Blade Angle on Blade Stresses During Cutting of Different Kinds of Paper Materials
... the maximum tension stress distribution is grouped over the section that has been angled near the blade ...For von Mises stresses it is collected from under the guiding point and a certain ...
8
Structural Analysis of Disc Brake Rotor for Different Materials
... the Maximum principal Stresses induced in Titnium-2 which is ...The maximum von- Mises Stress induced in Titanium-2 which is ...the Von-Mises stress are also less compared ...
7
Parametric Analysis of Bus Bars in Silicon Cell of Photovoltaic (PV) Module under Static Wind Loads
... The von-Mises stresses observed in different layers of PV module at 28°C for four bus-bars with various BB thicknesses are given in T ABLE ...IV. Maximum von-Mises stress and ...
7
Finite Element Analysis of In Plane Displacements and Von Mises Stresses in Ellipsoidal and Circular Cylinderical Petroleum Tankers
... and Von-Mises stress (Figure 10) and that be- tween in-plane displacements and internal pressure (Fig- ures 12 and 13) are not unexpected because of the linear- ity of the stress-strain relationship in the ...
11
Modeling and Structural Numerical Analysis of a Cylindrical Pressure Vessel Using the Standard ASME PCC-2-2008
... problem using statically indeterminate using deformations equations. The Figure (2) shows a laminated cylinder which was built by heating a sleeve until she could slip on the tube. Heating the sleeve is required for ...
8
MECHANICAL BEHAVIOR ANALYSIS OF GFRP AND STRUCTURED STEEL FOR A FLAT PLATE UNDER TENSILE LOAD USING ANSYS
... Principle stresses are those stresses in principle planes where the shear stresses is ...the maximum tensile stress induced in the flat plate due to loading ...the maximum compressive ...
7
EXPERT MODELLING AND PREDICTION OF VON MISES STRESSES IN CARBIDE INSERT CUTTING TOOL USING FEM (ANSYS)
... residual stresses induced by dry turning on difficult- to- machined ...(residual stresses) and surface integrity while turning Inconel 718 and Austentic stainless steel AISI 318L under dry condition with ...
12
Finite Element Modeling for Linear Analysis of Disc Brake
... 12 shown below is the von mises stress diagram of the Aluminum obtained in the stress analysis performed in ANSYS APDL Software. It can withstand a maximum von mises s[r] ...
7
Paper 02-2013-1
... temperature, Von Mises stress and the total deformations of the disc and contact pressures of the pads increase as the thermal stresses are added to mechanical stress which causes the crack ...
11
Comparative FE Analysis of Pressure Vessel of Hemispherical, Ellipsoidal and Torospherical End Connection
... The use torospherical end results in the lengthwise reduction of the vessel. Here the length is reduced to nearly thrice the one which is with hemispherical end but at the same time the knuckle radius is used here for ...
5