parametric finite-element models
Primary Stress Index B2* for the Evaluation of postulated or detected Circumferential Flaws at the Connection Straight-Pipe / Bend
... two parametric finite element models for circumferential surface cracks in straight-pipes and for the same flaws and the connection ...
8
Finite Element Analysis of New Circular Lateral Bracing System: A Parametric Study
... D.C. Rai et al. (2003) [1] conducted an analytical seismic behavior study of "ordinary" concentrated braced steel frame structures to withstand upcoming earthquakes. Development can be attained by converting the ...
7
Parametric Analysis of Friction Stir Welding Using Finite Element Tool
... The equation of motion for friction stir process is solved by using finite element tool ANSYS 14.5. However, the direct simulation the welding processes is not possible; therefore coupling of various ...
9
Parametric Study on Behavior 0f Box Girder Bridges Using Finite Element Method
... 3D models and carry out all the ...The parametric modeler allows the user to build simple or complex bridge models and to make changes efficiently while maintaining total control over the design ...
8
Parametric Study of Hot Rolling Process by the Finite Element Method
... The contact problem has not been much con- sidered in past literature. However, because of its nonlinear nature and its complex condition, it is very important to consider it particularly. Combining the nite ...
10
Moment resistance and rotation capacity of semi-rigid composite connections with precast hollowcore slabs
... [18], parametric study of the effect of the flange thickness is ...3-D finite element models (CJ1, Flange88, Flange44 and Flange22) were ...four models, all other conditions were kept ...
23
Parametric finite-element studies on the effect of tool shape in friction stir welding
... As found previously, the shoulder surface angle, tool , has little effect on the heat generation. Therefore, it is expected that it should not have much effect on temperature distribution in the workpiece. From ...
37
A parametric finite element solution of the generalised Bloch-Torrey equation for arbitrary domains
... the finite difference method [8, 9, 10], the finite volume method [11], and the finite element (FE) method [12, 13]. The latter is generally preferred owing to its flexibility for spatially ...
27
Parametric Optimization of the Output Shaft of a Portal Axle using Finite Element Analysis
... The shaft models were modelled using FEA and validated through comparisons with the experimental results. In the analysis of the output shaft of the portal axle, the hollow shaft with a rib is proposed and the ...
7
A PARAMETRIC STUDY OF WINDTURBINE SPARCAP IN BASALT FIBER USING FINITE ELEMENT ANALYSIS
... A parametric FEA model of Spar cap of wind turbine is established using ANSYS ...a parametric model, which means that the structural parameters of Spar Cap can be easily modified to create various ...The ...
8
FINITE ELEMENT MODELLING AND ANALYSIS OF INDIAN TECTONIC PLATE
... elastic finite element model will be created by considering an appropriate number of elements so that the required spatial resolution of both latitude and longitude is ...
7
Introduction to Finite Element Analysis of Fillet Welded Joint
... and finite element prediction The multiple-site damage (MSD) phenomenon is discussed, and exemplified by the behaviour of riveted lap-joint specimens of aluminum alloy 2024-T3 ...
6
Experimental and analytical investigation of ferrocement water pipe
... up to failure under two-point loading system. Their results showed that the proposed composite beam has good ductility, cracking strength and ultimate capacity more than reinforced concrete beam. Shannag and Ziyyad ...
11
Experimental & Finite Element Analysis of Strength of a Fillet Weld for two 1020 MS Plates
... Abstract: T-joint fillet welding is the most common welding in engineering applications. Transport vehicles, marine ships, mobile plant equipment are few examples where fillet welding are used extensively. Analysis of ...
9
Finite Element Analysis and Parametric Study of Schwedler Dome Using ABAQUS Software
... Schwedler dome shows good performance against the horizontal loads. Due to its structural symmetry and shape provide dome good performance against horizontal loading. Providing diagonal elements to the dome structures ...
6
Modeling of Mechanical Behavior of Notched Composite Laminates
... A finite element model was developed using Ansys Parametric Design Language (APDL) to predict the notched strength and the damage growth during tensile loading taking into consideration the ...
6
The determination and evaluation of Nitinol constitutive models for finite element analysis
... Variation with Temperature. Experimental data was input into the computational model at temperatures of Af+10°C and Af+40°C in order to set up temperature dependant material properties within the finite ...
8
Structural Analysis of Mono-Symmetric Plate Girders in Composite Bridges
... actual finite element model the height of the web was modelled having a depth of 1000 mm plus half the thickness of both the compression flange and the tension ...
11
Analysis of the Behavior of Inclined Anchor by Varying the Inclination and Elevation of Tie
... the finite element technique in their analysis to investigate the behavior and failure mechanisms of the structure (Bilgin (2009), Warrington and Don, 2007; Krabbenhoft et ...
18
Simulation of Fast Reactors with the Finite Element Method and Multiphysics Models.
... In this simulation, two thermal hydraulic models are developed. The first is a steady-state, one- dimensional, axial heat convection model to calculate bulk coolant temperatures and densities as the coolant flows ...
164