Tensile Tests
Statistical approaches in tensile tests of bond strength
... tests of restorative materials, Burrow et al.19concluded that Weibull analysis is suitable test to determine the reliability of strength measurements. In this study, the obtained data were submitted to Weibull ...
6
Mechanical Behavior of V-shaped Specimens Optimized for Slow Strain Rate Tensile Tests
... rate tensile specimens was particularly convenient for evaluating the susceptibility to intergranular stress corrosion cracking of nickel-base ...tensile tests. Validation of proposed modelling ...
7
First Principles Tensile Tests of Tilt and Twist Grain Boundaries in Al
... first-principles tensile or shear testing simulations of GBs 3) are quite ...under tensile or shear stresses based on the accurate description of electrons and atoms by the density- functional theory (DFT), ...
7
Slow strain rate tensile tests on irradiated austenitic stainless steels in simulated light water reactor environments
... rate tensile tests were performed on neutron irradiated Types 304 and 304L SSs in high-DO BWR and PWR ...SSRT tests in high- DO BWR water produced similar results in both Halden and BOR-60 ...
9
Tensile tests of glass powder reinforced epoxy composites: pilot study
... and tensile strengths as well as Young modulus and cost was five ...if tensile properties were the most important factors to be considered in the applications of the composites, glass powder is not a ...
5
Re-examination of the mechanical anisotropy of porcine thoracic aorta by uniaxial tensile tests
... biaxial tensile tests [3], physiologically-simu- lated test (cylindrical arterial segments subjected to an internal pressure and axial pre- stretch without torsion and shear [4]), digital image correlation ...
14
Modeling root reinforcement using a root failure Weibull survival function
... 43 tensile tests with root segments excavated at the same location where the pullout tests were performed (a forested site dominated by Spruce at Üetliberg near Zürich (Switzerland) − ...and ...
11
LOW CYCLE FATIGUE LIFE PREDICTION OF GTD 111 SUPERALLOY FOR USE IN GAS TURBINE BLADES
... of tensile tests at room temperature and 9000C.The tensile test at room temperature was performed once and the tensile tests at 9000C were performed ...The tensile strength of ...
8
Evaluation of mechanical properties of TIG welding joint of stainless steel 304
... and tensile test of 304 stainless steel joints by tungsten inert gas (TIG) ...welding. Tensile tests and Hardness were performed and the fracture surfaces were ...highest tensile strength and ...
6
Influence of the Mix Parameters and Microstructure on the Behaviour of Concrete at High Temperature
... several tests : compression and splitting tensile tests, measurement of modulus of elasticity, heating – cooling cycles, measurements of thermal field and mass loss during the heating – cooling ...
9
Synthesis and Characterization of Polyamide-66/Calcium Carbonate Composites
... (Tensile Tests): Tensile strength, Young’s modulus and percent elongation at yield and break were measured at room temperature according to ASTM-D882 [7] by Zwick 1445 Universal Testing Machine ...
16
High strain rate and quasi-static tensile behaviour of Ti-6Al-4V after cyclic damage
... the tensile properties of materials [1–9], including various steel grades and light ...of tensile tests at quasi-static and / or high strain rates after a given cyclic load had been ...the ...
6
Some investigations about the tensile strength and the desiccation process of unsaturated clay
... the tensile strength of unsaturated clay, and a discussion about the significant differences between the behaviours of compacted soils and those of the completely remoulded ...the tensile strength is also ...
8
Engineering Design Driven by Models and Measures:
... - the remaining resins have similar behaviour with a slight preference for isonepentilic resin. Diagram and standard limits for: a) tensile tests; b) flexural tests; c) interlaminar shea[r] ...
12
Mechanical Properties of Al Al2O3 Composites Part I: SAP ISML EUR 4074
... Finned Tubes Tensile Tests Compression Tests Burst Tests Influence of Internal Artificial Defects on the Transverse Mechanical Properties of Finned Tubes 3.3.2.5 Fatigue Tests in Compres[r] ...
238
Effect of Titanium Carbides on the Ductility and Toughness of High Carbon 30 mass% Chromium Steels
... In the previous papers, 1–10) the author reported that mechanical properties such as ductility, toughness, and fatigue strength of 30 mass% Cr ferritic steels are markedly influenced by the volume and morphology (which ...
6
Properties of Moldings Prepared from LDPE-Pumpkin Seed Hulls Blend
... The tests were conducted using a single-screw injection molding machine, marketed under the name of ARBURG ALLROUNDER ...static tensile tests were performed on produced composite molded pieces using ...
8
Interface Microstructure and Mechanical Properties of Dissimilar Friction Stir Welded Joints between Zr55Cu30Ni5Al10 Bulk Metallic Glass and Pure Al
... After FSW, thermal stabilities of thin BMG plates cut close to the joint interface were measured by differential scanning calorimetry (DSC, Bruker, DSC 3300SA) at a heating rate of 20 K/min in a flowing Ar gas atmosphere. ...
7
Synthesis and Properties of Waterborne Polyurethane (WBPU)/Modified Lignin Amine (MLA) Adhesive: A Promising Adhesive Material
... hydrophobicity and thermal resistance [24]. Although there have been some attempts to use larger alkyl chains in different ways, the larger alkyl groups lead to WBPU dispersion challenges. Increasing the DMPA content is ...
22
Development and Mechanical Characterization of Palmyra Fruit Fiber Reinforced Epoxy Composites M. Venkateswarlu, M. Ashok Kumar, M. Nagakiran
... the tensile tests that the tensile strength and modulus increases with the increase in volume fraction of ...showed tensile strength around 22 MPa whereas in this case it is found to be around ...
5