• No results found

voltage pulse

High-voltage Pulse Generation Using Electrostatic Induction in Capacitor

High-voltage Pulse Generation Using Electrostatic Induction in Capacitor

... Abstract: Pulse power sources can produce high temperature or high-density extreme conditions within a short ...high voltage pulse sources using insulated-gate bipolar transistor (IGBT) ...

10

A Step Up Modular High Voltage Pulse Generator Based on Isolated Input Parallel/Output Series Voltage Boosting Modules and Modular Multilevel Sub modules

A Step Up Modular High Voltage Pulse Generator Based on Isolated Input Parallel/Output Series Voltage Boosting Modules and Modular Multilevel Sub modules

... rectangular pulse-waveforms can be generated by MMC based PGs, but a wide range of pulse-waveforms is also possible [5] and ...obtained pulse peak-voltage is that of the input HVDC ...

10

Influence of Machining Parameters on Electro Discharge Machining of NiTi Shape Memory Alloys

Influence of Machining Parameters on Electro Discharge Machining of NiTi Shape Memory Alloys

... levels. Pulse on time and off time varied from 35-100 μs, and 30-200 μs, ...current, voltage, pulse on time and pulse off time. The voltage factor has two levels and the rest of the ...

10

Comparison of Brass and Zinc Coated Wire Electrode Using Wire Cut EDM Concerning MRR of Machining SS304

Comparison of Brass and Zinc Coated Wire Electrode Using Wire Cut EDM Concerning MRR of Machining SS304

... like pulse on time, pulse off time and voltage on the material removal rate of wire electric discharge ...machining voltage, pulse on time, pulse off time, wire feed, wire ...

7

Influence of Pulse Duration on Electric Discharge in Dielectric Medium

Influence of Pulse Duration on Electric Discharge in Dielectric Medium

... input voltage is controlled by the autotransformer and the frequency controller sets the desired frequency and duty ratio of the voltage ...input voltage shape and to detect the circuit ...

6

Strategic Optimization and Investigation Effect Of Process Parameters On Performance Of Wire Electric Discharge Machine (WEDM)

Strategic Optimization and Investigation Effect Of Process Parameters On Performance Of Wire Electric Discharge Machine (WEDM)

... open voltage has the greatest effect on surface roughness and is followed by wire tension, pulse on time, servo voltage, pulse off time, fluid pressure, feed rate over ride and wire feed in ...

7

Development of a Measurement Software for the Characterization of WORM Devices for Novel Memory Storage Applications

Development of a Measurement Software for the Characterization of WORM Devices for Novel Memory Storage Applications

... a voltage pulse which induces the formation of a stable con- ductive bridge (short-circuit) between the two ...cyclic voltage-sweep between two limit ...the voltage in a well-defined range, ...

13

Measurement and control of the streamer head electric field in an atmospheric-pressure dielectric barrier plasma jet

Measurement and control of the streamer head electric field in an atmospheric-pressure dielectric barrier plasma jet

... positive voltage pulse to the external electrodes a drop in the streamer head electric field was observed, confirming the experimental and computational results reported previously by Naidis and Walsh ...

16

Optimization of kerf width obtained in 
		WEDM of Aluminum hybrid composite 
		using Taguchi method

Optimization of kerf width obtained in WEDM of Aluminum hybrid composite using Taguchi method

... Muthu Kumar V et al. (2010) demonstrates optimization of Wire Electrical Discharge Machining process parameters of Incoloy800 super alloy with multiple performance characteristics such as Material Removal Rate (MRR), ...

7

Current Mode Double Edge Triggered Flip Flop with Enable

Current Mode Double Edge Triggered Flip Flop with Enable

... global voltage generator by using current ...current-to-voltage pulse generation is done by the current comparator and that signal is amplified by using the ...current-to-voltage pulse ...

6

Optimization of Wire Electrical Discharge Machining Process Parameters on kerf width in Machining of Titanium Alloy using Response Surface Methodology

Optimization of Wire Electrical Discharge Machining Process Parameters on kerf width in Machining of Titanium Alloy using Response Surface Methodology

... of pulse on time and servo voltage, pulse off time and servo voltage, pulse current and wire tension are significant model terms. The values greater than 0.1 indicates that the model ...

6

Adoption of M- Wallet: A way Ahead

Adoption of M- Wallet: A way Ahead

... namely pulse on time, pulse off time, peak current and servo voltage with dimensional ...of pulse on time, pulse off time, peak current and servo voltage and interaction effect ...

5

Development a series ignition circuit for simmer operation of Nd: YAG flashlamp driver

Development a series ignition circuit for simmer operation of Nd: YAG flashlamp driver

... negative voltage pulse signal with the same amplitude of DC supply is generated at primary winding as shown in Figure ...the voltage approximately up to 12 ...winding voltage without the ...

5

Experimental Observation of Pulse-Shortening Phenomena in Traveling-Wave Field Effect Transistors

Experimental Observation of Pulse-Shortening Phenomena in Traveling-Wave Field Effect Transistors

... the pulse-shortening phenomena in traveling-wave field effect transistors ...decreasing voltage pulse is applied to the gate line and an increasing voltage pulse is simultaneously ...

10

Renewable Power Application based Switched Boost Inverter

Renewable Power Application based Switched Boost Inverter

... output voltage. The inverter Output voltage and its harmonic spectrum, proves that the “shoot-through state of SBI will have no effect on the harmonic spectrum of its output voltage provided that the ...

7

Optimization of Materiel Removal Rate for AL6063-T6 on WEDM Using Response Surface Methodology

Optimization of Materiel Removal Rate for AL6063-T6 on WEDM Using Response Surface Methodology

... as pulse on (Ton) ,pulse off (Toff), peak current (Ip), servo voltage (Sv) for analysis the material removal rate (MRR) while machining EN5 mild steel ...

7

Simulation as an effective tool to compare the performance of SPWM and SVPWM fed two level inverter

Simulation as an effective tool to compare the performance of SPWM and SVPWM fed two level inverter

... (b) Pulse Width Modulation [PWM] control. Pulse width modulation is a technique in which a fixed dc input voltage is given to the inverter and a controlled ac output voltage is obtained by ...

5

Effects of Pulse Voltage on the Droplet Formation of Alcohol and Ethylene Glycol in a Piezoelectric Inkjet Printing Process with Bipolar Pulse

Effects of Pulse Voltage on the Droplet Formation of Alcohol and Ethylene Glycol in a Piezoelectric Inkjet Printing Process with Bipolar Pulse

... The experimental setup for the DOD droplet formation is shown schematically in Fig. 1 and flash photography is utilized to observe the evolution of the liquid droplet. A control system includes a strobe driver, waveform ...

8

Design and implementaion of Space-Vector PWM Control Synthesis for an H-Bridge Drive In Electrical Vehicles

Design and implementaion of Space-Vector PWM Control Synthesis for an H-Bridge Drive In Electrical Vehicles

... Variable voltage and frequency supply for Adjustable Speed Drives (ASD) is invariably obtained from a three‐phase ...DC voltage across the load in a specific pattern will appear to the load as an AC signal, ...

5

Ignition of a Liquid Fuel Jet by an Electrical Discharge Propagating along the Jet.

Ignition of a Liquid Fuel Jet by an Electrical Discharge Propagating along the Jet.

... same voltage will increase the electric field strength at all points between the ...in voltage of 30-40% if we compare the voltages at which spraying began and stabilized into ...

163

Show all 10000 documents...

Related subjects