[PDF] Top 20 Comparison of Two Methods of Chlorhexidine Application of Shear Bond Strength Degradation between Composite Resin and Dentin
Has 10000 "Comparison of Two Methods of Chlorhexidine Application of Shear Bond Strength Degradation between Composite Resin and Dentin" found on our website. Below are the top 20 most common "Comparison of Two Methods of Chlorhexidine Application of Shear Bond Strength Degradation between Composite Resin and Dentin".
Comparison of Two Methods of Chlorhexidine Application of Shear Bond Strength Degradation between Composite Resin and Dentin
... in shear bond strength of Group 1 (bonding) after 10% NaOCl immersion from ...inhibited degradation and increases the bond strength of composite resin and ... See full document
6
Comparison of Bromelain Enzyme, Sodium Hypochlorite, and Titanium Tetrafluoride on Shear Bond Strength of Restorative Composite to Dentin: An in vitro Study
... the dentin. Two consecutive coats of Adper single bond (3M, ESPE, ...the dentin surface by a disposable ...nanofilled composite resin (Z350; 3M, ES- PE, USA) was embedded in a ... See full document
7
Shear Bond Strength of Self-Adhesive Flowable Composite, Conventional Flowable Composite and Resin-Modified Glass Ionomer Cement to Primary Dentin
... lower bond strength compared to the use of conventional composites and total etch bonding systems ...flowable composite, which was in line with the findings of a previous study ...the bond ... See full document
7
Influence of povidone-iodine on micro-tensile bonding strength to dentin under simulated pulpal pressure
... 2% chlorhexidine solution for 60 s in group 2, and in water in the control group (no ...The dentin surface was dried for 10 s with an oil-and-water-free air source with pressure to remove excess water and ... See full document
7
Effect of an Extra Hydrophobic Resin Layer on Repair Shear Bond Strength of a Silorane-Based Composite Resin
... silorane-based composite resins is approximately 1% ...methacrylate-based composite resins ...this composite resin makes it highly ...silorane-based composite resin, the bonding ... See full document
9
Evaluation of Shear Bond Strength of Total- and Self-etching Adhesive Systems after Application of Chlorhexidine to Dentin Contaminated with a Hemostatic Agent
... which chlorhexidine is ap- plied, some authors have used chlorhexidine after etch- ing and showed higher bond strength ...that chlorhexidine has been shown to inhibit enzyme activities ... See full document
7
Effect of 2% Chlorhexidine on the Bond Strength of Direct Composite Restoration to Dentin: An in vitro Study
... the shear bond strength values showed a statistically significant difference (p < ...0.01) between the two groups, with higher values for the CHX ...the resin–dentin ... See full document
5
In-Vitro Evaluation of the Effect of Herbal Antioxidants on Shear Bond Strength of Composite Resin to Bleached Enamel
... [23]. Two in-vitro studies demonstrated that grape seed extract inhibited the demineralization and enhanced the remineralization of carious root lesions ...of shear bond strength testing in ... See full document
8
Repair Bond Strength of Composite to Zirconia Ceramic Using Two Types of Zirconia Primers
... repair bond strength of composite to zirconia ...of application of two types of Materials and Methods: In this in vitro, experimental study, 60 zirconia blocks were divided into ... See full document
9
The Effect of Disinfection with Chlorhexidine on the Shear Bond Strength of Equia Resin-Modified Glass Ionomer Cement to Dentin in Permanent Teeth after Two Thermocycling Protocols
... interaction between RMGIs and tooth ...CHX application on the shear bond strength of Equia RMGIC to dentin after two thermocycling ... See full document
7
Evaluation and Comparison of Shear Bond Strength of Glass Ionomer, Resin modified Glass Ionomer and Composite Resin in Primary Molars: An Invitro study
... techniques to identify 3 factors that are involved in the adhesion of a light activated glass ionomer liner to dentin. First, penetration of the glass ionomer through the smear layer and into the dentinal tubules ... See full document
57
Comparison of Endodontic Medicaments on Bond Strength of Fiber Post to Root Dentin Using Resin Cement
... F2 resin cement (Kuraray, Japan) according to the manufacturer’s instructions and light cured using a light curing unit (Ledturbo, USA) with 2,100mW/cm2 of curing power for 20 seconds from coronal ...acrylic ... See full document
5
Resin-modified Glass Ionomer Cement and its Use in Orthodontics - Concept Old is Gold: View Point
... modified resin GIC, the simplest form of GI cement which contains a small quantity of a water-soluble and polymerized resin component is widely used restorative material and in orthodontic practice also ... See full document
5
Effect of four different conditioners on the shear bond strength of composite to glass ionomer: An In vitro study
... measure shear bond strength, the specimens were placed in between the jigs of the universal testing machine and a pointed shearing rod was placed on to the composite resin/glass ... See full document
91
Comparative evaluation of fluoride release and shear bond strength of a polyacid - modified composite resin, a resin modified glass ionomer cement and a conventional composite resin: An Invitro study
... a resin reinforced glass ionomer (Fuji Ortho LC,) and compared it with a more traditional light-cured bonding system (Transbond,) that contained resin material ...The shear bond ... See full document
101
Effect of Layering Technique on Push-Out Bond Strength of Composite Resin to Intracanal Dentin of Primary Anterior Teeth
... junction (CEJ), perpendicular to the long axis of the teeth using a high-speed handpiece (NSK, Tokyo, Japan) and a fissure diamond bur (No. 138, Jota AG, Switzerland) under water irrigation. The teeth were randomly ... See full document
9
Shear bond strength between alumina substrate and prosthodontic resin composites with various adhesive resin systems
... prosthodontic resin composites [BelleGlass®, (BG, Kerr, CA, USA), Sinfony® (SF, 3 M ESPE, Dental Products, Germany), and GC Gradia® (GCG, GC Corp, Tokyo, Japan)] were bonded to the alumina substrate using four ... See full document
11
Shear Bond Strength of Orthodontic Brackets to Composite Restorations Using Universal Adhesive
... the bond strength between the luting composite and the old composite restoration ...preparation methods include sandblasting and surface roughening by diamond bur ...Chemical ... See full document
8
Statistical approaches in tensile tests of bond strength
... the dentin area and divided into 2 groups/N=24: macro- tensile and ...of dentin in 2 ...acrylic resin (Jet- Articles Odontológicos Clássicos ...Brazil). Dentin was etched with 37% ... See full document
6
Evaluation of Bond Strength of Metal-Resin using Different Modes of Mechanical Retention: An In Vitro study.
... three methods of etching metal for resin-bonded retainers namely: Met-Etch gel (Gresco Products, ...to bond Comspan (L . D .Caulk Co., Milford, Del) composite luting ...material. Shear ... See full document
80
Related subjects