• No results found

3D laser scanner

An experimental study to test a 3D laser Scanner for body measurement and 3D virtual garment design in Fashion education

An experimental study to test a 3D laser Scanner for body measurement and 3D virtual garment design in Fashion education

... initial 3D scanner tests on a body, found that human skin, ecru and white matt fabrics reflect light and give highly accurate ...the scanner resulting in no data being ...the 3D laser ...

15

The Study On The Effect Of Faroarm  - 3D Laser Scanner In Different Scanning Depth, Scanning Angle And Temperatures Condition

The Study On The Effect Of Faroarm - 3D Laser Scanner In Different Scanning Depth, Scanning Angle And Temperatures Condition

... – 3D Laser Scanner in different scanning depth, scanning angle and temperatures ...Faroarm-3D laser scanner, the workpiece will be scanned and the information will be send to the ...

24

The scope in the INTELCITIES project for the use of the 3D laser scanner

The scope in the INTELCITIES project for the use of the 3D laser scanner

... the 3D Laser scanner has enormous potential to benefit Chartered Building Surveyors and their clients in terms of accuracy, speed and productivity in plan preparation and then to extend the range of ...

13

Virtual building maintenance: Enhancing building maintenance using 3D GIS and 3D laser scanner (VR) technology

Virtual building maintenance: Enhancing building maintenance using 3D GIS and 3D laser scanner (VR) technology

... GIS software will be used to generate and analyse thematic developments relating to the building properties and associated maintenance management strategies. ArcGIS 3D analyst, for example, enables users to ...

8

TRIMBLE TX5 3D LASER SCANNER QUICK START GUIDE

TRIMBLE TX5 3D LASER SCANNER QUICK START GUIDE

... Connect the cable of the power supply unit to the power socket of the laser scanner. Use the end with the 90° bend connector. Confirm the direction of the power supply’s plug. If you forcibly insert the ...

8

Development of a 3D laser scanner for guiding a six-legged walking robot

Development of a 3D laser scanner for guiding a six-legged walking robot

... time 3D kinematic model of the walking robot, joint angle data and data from 3 tilt sensors (accelerometers) on the robot body will allow the controller to accurately estimate the “(x, y)” position for the robot’s ...

11

keywords Tangible user interface, 3D laser scanner, landscape design

keywords Tangible user interface, 3D laser scanner, landscape design

... The second implementation uses infrared light to capture the surface geometry of a landscape model. A sand 3 box is lit from underneath with a powerful source of infrared light. A monochrome infrared camera mounted above ...

6

A Moving 3D Laser Scanner for Automated Underbridge Inspection

A Moving 3D Laser Scanner for Automated Underbridge Inspection

... • the lateral and vertical motion of the cart are measured by the spot camera, which identifies the. 129[r] ...

14

Realization and Verification of Data Conversion from Laser Scanner to FEM

Realization and Verification of Data Conversion from Laser Scanner to FEM

... This paper deals with the data processing in the form of a point cloud scanned using a handheld 3D laser scanner. The aim of the paper was to use this data to create a representative FEM model and ...

6

Three dimensional asset documentation using terrestrial laser scanner technology

Three dimensional asset documentation using terrestrial laser scanner technology

... The 3D laser scanner is also called an active remote sensing system because no additional personnel are needed to hold a ranging pole or to place targets for measuring surfaces, which are not ...

18

Terrestrial laser scanner for 3D modelling of USQ Toowoomba campus

Terrestrial laser scanner for 3D modelling of USQ Toowoomba campus

... commencing laser scanning, investigation of the subject area was conducted to determine number of scans needed to fulfil project objectives as well as position of individual ...Focus 3D laser ...

69

Printing Roll Manufacturing using Laser Scanner

Printing Roll Manufacturing using Laser Scanner

... fiber laser system, whereas the moving unit consists of the X-Y table, roll rotating axis, 3D laser scanner, and optical ...the 3D laser scanner system instead of the ...

6

Laser-scanner used in a wind tunnel to quantify soil erosion

Laser-scanner used in a wind tunnel to quantify soil erosion

... a 3D laser scanner inside a wind tunnel, to relate the change in soil micro-relief to soil ...low-cost laser scanner in a wind tunnel for examining the wind- dependent variation in soil ...

6

Build 3D Scanner System based on Binocular Stereo Vision

Build 3D Scanner System based on Binocular Stereo Vision

... There are a lot of methods can finish 3D scanning. Each method has its different limitations, advantages and costs. The paper proposes a non-contact and low-cost 3D laser scanner system. This ...

6

Deformation monitoring of a steel structure using 3D terrestrial laser scanner (TLS)

Deformation monitoring of a steel structure using 3D terrestrial laser scanner (TLS)

... between laser scanner position and the structure during measurement was important to be considered in order to define a filtering procedure in the ...the laser scanner data does not only ...

10

A Comparison of the Terrestrial Laser Scanner & Total Station for Scene Documentation

A Comparison of the Terrestrial Laser Scanner & Total Station for Scene Documentation

... the laser scanner has been used in some capacity at ...the laser scanner. Scanner data accuracy is often a complex question because of the way in which manufacturers report accuracy, ...

8

Processing laser scanner plant data to extract structural information

Processing laser scanner plant data to extract structural information

... handheld laser scanner [2,3] is an elegant combination of an optical and an electromagnetic device (Figure ...red laser light to be ...the laser line with the surface of the object (the ...

5

RECOGNISING STRUCTURE IN LASER SCANNER POINT CLOUDS 1

RECOGNISING STRUCTURE IN LASER SCANNER POINT CLOUDS 1

... Several variations can be made to the above principle. Sithole and Vosselman (2003) describe a scan line segmentation method that groups points on scan lines based on proximity in 3D. These groups do not need to ...

6

The Use of Laser Scanner in Caves, Encountered Problems and Solution Suggestion

The Use of Laser Scanner in Caves, Encountered Problems and Solution Suggestion

... terrestrial laser scanners in removing the three-dimensional model of the caves and to provide solutions to the problems ...terrestrial laser scanners are usable for the cave mapping and method that allows ...

8

Mesoscale Laser 3D Printing

Mesoscale Laser 3D Printing

... femtosecond 3D optical printing of objects at the meso-scale (from sub-m to sub-cm spanning five orders of ...the laser printing well aligned with similar approaches in nanofabrication by electron and ion ...

20

Show all 9969 documents...

Related subjects