• No results found

finite element model analysis

Analysis   on the Buckling Behavior of the Spacer Grid Structure for the PWR Fuel Assembly

Analysis on the Buckling Behavior of the Spacer Grid Structure for the PWR Fuel Assembly

... In addition, the finite element analysis model is in good agreement with the impact test results, therefore this finite element model and the analysis procedure will be [r] ...

8

Finite Element Of Human Spine CAD Model Analysis

Finite Element Of Human Spine CAD Model Analysis

... thesis, Finite Element method use CAD model to be analyzed. Finite element is the best method that can be used to visualize stress distribution on lumbar ...

24

DYNAMIC ANALYSIS AND STRUCTURAL DESIGN OF TURBO GENERATOR FRAME FOUNDATION – A REVIEW

DYNAMIC ANALYSIS AND STRUCTURAL DESIGN OF TURBO GENERATOR FRAME FOUNDATION – A REVIEW

... static analysis and dynamic analysis of turbine reinforced concrete foundations and also focuses on the load cases to be applied for ...complex finite element model was constructed to ...

6

Finite Element Analysis Of Bridge Cranes’ Proof Load Test Data

Finite Element Analysis Of Bridge Cranes’ Proof Load Test Data

... The assembly and solution of a simple model is illustrated using a two element idealization for a uniform beam of length 2L. The problem to be solved and the model used are shown in Figure1in ...

16

Analytical and Experimental Investigation of I Beam-to-CFT Column Connections under Monotonic Loading (RESEARCH NOTE)

Analytical and Experimental Investigation of I Beam-to-CFT Column Connections under Monotonic Loading (RESEARCH NOTE)

... global analysis or under seismic ...finite element program ABAQUS compared against experimental data by Hsuan-Teh Hu et ...the finite element model of this experimental specimen is ...

14

Finite element model of a double-stage helical gear reduction.

Finite element model of a double-stage helical gear reduction.

... ANSYS model was built using BEAM188, MASS21, COMBIN14, and MATRIX27 ...beam element for 3D analysis. MASS21 is a structural mass point element also suitable for 3D ...per element w ith ...

117

Finite Element Analysis of High Pressure Composite Vessels

Finite Element Analysis of High Pressure Composite Vessels

... H. Medhavi Sinha et. al. have done her investigation, the limited component model of CFRP, tube shaped composite weight vessel is built up utilizing limited component programming ANSYS 11. The models got for ...

12

DESIGN ANALYSIS OF LOWER CONTROL ARM OF MAC PHERSON SUSPENSION SYSTEM

DESIGN ANALYSIS OF LOWER CONTROL ARM OF MAC PHERSON SUSPENSION SYSTEM

... the finite element analysis is carried out. The baseline model of the lower control arm is created by using solid modeling software ...for Finite Element Analysis This ...

5

Finite element model of the bed

Finite element model of the bed

... Analysis of response of bed construction on mentioned mechanical loading with geometry derived from design documentation and selected material combination was realized. In terms of discussed results can be say ...

6

The impact of temperature on wave interaction with damage in composite structures

The impact of temperature on wave interaction with damage in composite structures

... analytical finite element (SAFE) model is developed in [18] to predict guided wave response under varying temperature in ...lines analysis [19, 20], wavelet decomposition [21] and direct Lamb ...

38

Finite Element Analysis of an In Vitro Traumatic Joint Loading Model

Finite Element Analysis of an In Vitro Traumatic Joint Loading Model

... between model and pressure film impaction width and area data was ...impaction model. This would have also changed the finite element 2 dimensional reduction from a plane strain model ...

182

Original Article Three-dimensional finite element stress analysis on non-bridge external fixation to distal radius fracture

Original Article Three-dimensional finite element stress analysis on non-bridge external fixation to distal radius fracture

... tion model and the 3-D stereo model of DRF equipped with AO NBEF were imported into large finite element analysis method, softwa- re ASNSYS ...3-D finite element ...

7

Thermal Stress Analysis of a Dam Wall by Finite Element Model

Thermal Stress Analysis of a Dam Wall by Finite Element Model

... distribution analysis is unavoidable. When a transient heat transfer analysis is performed in a dam safety evaluation, it would be convenient to identify the most critical time to carry out a complete ...

7

Finite-element model and modal analysis of grand piano soundboard

Finite-element model and modal analysis of grand piano soundboard

... je model desky ...liší. Model volně (free) síťovaný čtyřstěnnými lineár- ními prvky typu SOLID45 čítá celkem 16 319 prvků a 5 643 ...Tentýž model síťovaný stejným typem prvku ale za užití mapované ...

8

DESIGN IMPROVEMENT AND ANALYSIS OF TRACTOR TROLLEY AXLE BY USING CAD/CAM/CAE TECHNIQUES

DESIGN IMPROVEMENT AND ANALYSIS OF TRACTOR TROLLEY AXLE BY USING CAD/CAM/CAE TECHNIQUES

... work finite element analysis approach is used to modify existing rear axle of tractor ...axle finite element model was predicted after the dynamic load was imposed on ...For ...

10

Finite element analysis of mechanical properties for 2D woven Kenaf composite

Finite element analysis of mechanical properties for 2D woven Kenaf composite

... Finite element analysis and analytical methods are powerful tools for studying the mechanical properties of woven ...various finite element techniques and assumptions have been proposed ...

36

FINITE ELEMENT ANLYSIS OF EVALUATION OF RADIAL STRESSES IN HYDRO - ASSISTED DEEP DRAWING PROCESS

FINITE ELEMENT ANLYSIS OF EVALUATION OF RADIAL STRESSES IN HYDRO - ASSISTED DEEP DRAWING PROCESS

... CFD analysis is used to determination of fluid pressure with given punch speeds at radius using castor ...The element type is fluid 141 elements from flotran CFD library is selected for ...The ...

10

MULTIBODY DYNAMIC ANALYSIS AND SIMULATION OF ENGINE MODEL

MULTIBODY DYNAMIC ANALYSIS AND SIMULATION OF ENGINE MODEL

... HyperView is a complete post-processing and visualization environment for finite element analysis (FEA), multi-body system simulation, video and engineering data. The contour plot for displacement of ...

9

Experimental and analytical studies of cold-formed steel sections with web openings subjected to web crippling

Experimental and analytical studies of cold-formed steel sections with web openings subjected to web crippling

... the finite element model, the experimental failure loads were compared against the failure load predicted by the finite element ...the finite element ...the finite ...

8

ANALYSIS OF FULL LENGTH FINITE ELEMENT MODEL OF PROFILE AND TWISTED ENDODONTIC FILES

ANALYSIS OF FULL LENGTH FINITE ELEMENT MODEL OF PROFILE AND TWISTED ENDODONTIC FILES

... file model is more flexible than the Twisted file is more elastic than ProFile model, hence it allows dentist to operate with more ease in curved canals during the process of final ...

10

Show all 10000 documents...

Related subjects