three-dimensional finite element method analysis
Three‑Dimensions Modelling of a Jet Pile Construction in the Karolinka Dam
... presents three‑dimensional modelling of a jet pile construction, by using finite element method which is performed by Plaxis ...
12
Biomechanical comparison of three stand alone lumbar cages — a three dimensional finite element analysis
... the finite- element method to evaluate the biomechanical effects of the stand-alone ALIF cages on the kinematic and mech- anical behaviors of the adjacent tissues and ...cages. Three ...
13
A new method for the treatment of unilateral posterior cross-bite: a three-dimensional finite element stress analysis study
... an element with no shear stress ...an element will ever see under specified applied loads, like ham- mering a nail in one direction without causing ...
9
Three-dimensional simulation of human teeth and its application in dental education and research
... Voxel method in which material properties and different teeth structures are ...dental finite element analysis due to the definition of the properties of the teeth ...a method based on ...
7
Estimates for the pressure and thermal distortions of coating dies for use in design and simulation
... and three-dimensionally. A two-dimensional model has lower computational load and is preferred for die ...two-dimensional analysis of a coating die, the finite element ...
82
Two Dimensional and Three Dimensional Finite Element Analysis of Finite Contact Width on Fretting Fatigue
... To implement the proposed hybrid layer method, the convergences of traction distributions are investigated next. Traction distributions obtained from 3D global mesh and first submodeling at the center and edge of ...
8
Three Dimensional Finite Element Analysis of Wire Drawing Process
... 5.50mm from steel grade 0.46% carbon and 0.71% carbon were drawn to 1.35mm in 13 draws and two speeds 8m/sec and 25m/sec. After each draw, the following properties were determined; tensile strength (Ts), temperature (T), ...
12
Finite Element Analysis of EA 113 Gasoline Engine Connecting Rod
... the analysis of kinematics and dynamics. And then the three-dimensional model of connecting rod was established and transient dynamics analysis, modal analysis and analysis of ...
6
DESIGN VALIDATION OF THE EXISTING MUFFLER’S TRANSMISSION LOSS RESULTS WITH ACOUSTIC SIMULATION TOOL
... -load method is commonly used to predict the transmission loss of an Acoustic ...muffler. Finite Element Method is also used to show the comparative study of Transmission Loss of ...the ...
6
Three Dimensional Nonlinear Finite Element Analysis of Airport Pavements.
... many different parameters that may impact the test results in order to consider their effects on the test. In addition, it is often difficult to know why a specimen behaves in a certain manner because of the lack of ...
221
Original Article Three-dimensional finite element analysis of ankle arthrodesis
... Abstract: Background: Ankle arthrodesis is the gold standard and most commonly used method for the treatment of post-traumatic ankle arthritis. Aims: This study is to investigate the biomechanical safety and ...
10
Simulation Analysis on Shaking Table Test of RC Box-type Shear Wall in Multi-axis Loading (H192)
... paper, three dimensional nonlinear finite element analysis (3D-FEM) is applied to simulation analysis of the test results with simultaneous 3-direction input ...This ...
8
Evaluation of Principal strain and its direction due to three dimensional finite element stresses during Impact of structural dynamic load
... The analysis were made for the three dimensional finite element method and based on the above case studies the finite element strain , stress and direction were ...
15
Applications of Three Dimensional Finite Element Method in Orthodontics
... L. Three- dimensional finite element analysis of the craniomaxillary complex during maxillary protraction with bone anchorage vs conventional dental ...
5
An examination of traumatic mandibular fracture using three-dimensional finite element analysis
... the element resolution required to accurately model these structures would have resulted in a huge increase in processing time with no analysis ...and three orders of magnitude (Dorin Ruse, 2008; ...
369
Three-dimensional finite element analysis of the Japanese traditional post-and-beam connection
... A three-dimensional fi nite solid element model for Japanese traditional post-and-beam connections was devel- oped using the wood foundation method, which employed the concept of a beam on a ...
7
INVESTIGATIONS ON STRENGTH ANALYSIS OF LAP JOINTS FOR ALUMINUM- EPOXY COMPOSITE PLATES USING FINITE ELEMENT METHOD WITH EXPERIMENTAL VERIFICATION
... “Three- Dimensional Finite Element Analysis Of Single Bolted Aluminium Lap Joint And Validation By XRD Technique” International Journal of Mechanical And Production Engineering, ...
6
Application of Three Dimensional Crack Analysis Using Finite Element Alternating Method
... are three dimensional ...tolerance analysis, the calculation of fracture mechanics parameters for arbitrary three-dimensional surface and internal cracks remains an important task ...
7
Three Dimensional Finite Element Analysis of Pelvic Bone
... bearing element of human ...by three bone ileum, ischium and pubic symphysis having contribution 40% of the acetabulum, 40% of ischium and 20% of the pubis ...these three bones are separated by the ...
6
Three-Dimensional Finite Element Analysis of Material Nonlinearity
... of finite element method. A numerical study using the finite element method was developed by Antunes et ...the finite element analysis of three ...
9