Von Mises Stress-Strain
Analysis Of Single Point Incremental Forming Process To Fabricate Phosphorous Bronze Hemispherical Cups
... the von Mises stress, strain rate and thickness reduction of hemispherical cups of phosphorous bronze alloy, were sheet thickness, step size and coefficient of ...
6
Application of Artificial Neural Network to Analyze Hexagonal Plate with Hole Considering Different Geometrical and Loading Parameters
... In this study, linear elastic analysis of steel plates is performed, and results have been predicted using artificial neural network. The differences calculated between the maximum equivalent von Mises ...
13
Increasing Bending Strength of Aluminium Silicon Carbide Metal Matrix Composite Spur Gear by Increasing Fillet Radius
... presenting Von-mises ...maximum stress in the ...the strain at the root of the gear tooth, on the application of load of ...150N. Von-mises stress, strain and total ...
11
Numerical Investigation of Springback in Mechanical Clinching Process
... equivalent Von Mises Stresses and the total equivalent Plastic Strain obtained using FE simulation of the clinching process while Figure 2 shows the Von Mises stress in the Upper ...
8
The Continuum Stored Energy for Constitutive Modeling Finite Deformations of Polymeric Materials
... converted stress-strain curves in different deformation modes should coincide with its uniaxial tension stress-strain curve for both elastic and elastic-plastic ...equivalent stress ...
17
An Investigation into a Gear Based Knee Joint Designed for Lower Limb Prosthesis
... The gear-based knee joint designed for a transfemoral ampu- tee can recreate gait cycle movement of a healthy biological limb and can be used compatibly with adequate safety. According to the motion study results, the ...
15
Design and Analysis of Oil Pump for Improving its Efficiency in I C Engine
... Generally we use steel in design of gerotor and we compared with other materials such as aluminium, cast iron, titanium and magnesium. Therefore by above results we observed that von-mises stress ...
9
Integrated half bridge switch using 70 μm thin devices and hollow interconnects
... 20–23 compare the simulated maximum residual von 225 Mises stress and creep strain accumulation in the solder joints 226 for the die attachment and bump interconnects between the 227 ass[r] ...
11
Mechanical Analyses of Multi-piece Mining Vehicle Wheels to Enhance Safety
... The stress/strain analysis was performed through the commercial FE software code ...the stress life approach was ...and stress concentration were also taken into account using endurance-limit ...
318
Effect of off axis cell orientation on mechanical properties in smooth muscle tissue
... of strain and with higher off-axis alignment of ...of Von-mises stresses ob- tained indicate that the maximum shear stress values of tracheal smooth muscle increase with increasing values of ...
8
Meso scale numerical study of composite patch repaired hole drilled steel plate
... (von-Mises) stress and maximum equivalent elastic strain of the hole drilled steel plate by approximately ...on stress, strain and failure criteria within the ...Plywise ...
5
STRUCTURAL & THERMAL ANALYSIS OF IC ENGINE PISTON USING DIFFERENT MATERIAL
... Maximum von mises stress, Maximum von mises strain and Maximum deformation are less in Piston of Al 7050 T7451 alloy in comparison of Al 6061 & Gray cast ...
10
A Finite Element Model to Investigate the Impact of Torch Angle on an Autogenous TIG Welding Process
... plastic strain, Von Mises residual stress and distortion on the horizontal plate, were all suggest- ing only very minor sensitivity (typically less than 5%) to the torch angle vari- ...
11
Maximum von Mises Stress in the Sliding Contact of Coated Bodies
... the stress state in the contact of bi-layered bodies in ...the von Mises stress in the coating, as well as in the ...equivalent stress is influenced by the elastic modulus mismatch ...
12
Strain rate and thermal softening effects in shear testing of AA7075-T6 sheet
... larger strain levels, and consequently has the potential to result in thermal softening ...low strain rate experiments since the heat generated within the specimen is dissipated either through conduction to ...
6
An Exacting Wall-Penetration Pipe Analysis
... the stress state in the dented pipe wall is compared with the stress state during the flattening ...relevant stress indicators (stress intensities) at the uprated loading state were smaller ...
9
Computational Investigation of Potential Failure Modes in Arterial Hemodynamic Flowpath
... A few papers refer to arterial tissues fatigue as a mechanical phenomenon associated with increased circumferential and a shear stress level, inducing catastrophic rupture [25-27]. The concept of elastin fatigue ...
95
X-ray diffraction measurements of plasticity in shock-compressed vanadium in the region of 10-70 GPa
... By changing the laser energy at constant laser spot size over a number of experimental shots, we have obtained simi- lar x-ray diffraction images at approximately equally spaced points within the pressure range of 10–70 ...
15
The Tsai Wu failure criterion rationalised in the context of UD composites
... Using the obtained corrections for 2D in-plane stress conditions, the failure loci have been plotted in Fig. 2 for the materials shown in Table 2 for those satisfying >0 and they are compared with their ...
25
Paper 02-2013-1
... The main purpose of this study is to analyse the thermo-mechanical behavior of the dry contact between the brake disc and pads during the braking phase. The simulation strategy is based on computer code ANSYS11. The ...
11