Top PDF PARTNER Advanced Communications System Installation

PARTNER Advanced Communications System Installation

PARTNER Advanced Communications System Installation

Toll fraud, the unauthorized use of your telecommunications system by an unauthorized party (for example, persons other than your company’s employees, agents, subcontractors, or persons working on your company’s behalf) can result in substantial additional charges for your telecommunications services. You are responsible for the security of your system. There may be a risk of toll fraud associated with your telecommunications sytem. You are responsible for programming and configuring your equipment to prevent unauthorized use. Your system manager should read all documents provided with this product to fully understand the features that can introduce the risk of toll fraud and the steps that can be taken to reduce that risk. Lucent Technologies does not warrant that this product is immune from or will prevent unauthorized use of common-carrier telecommunication services or facilities accessed through or connected to it. Lucent Technologies will not be responsible for any charges that result from such unauthorized use. If you suspect you are being victimized by toll fraud and you need technical support or assistance, call the Lucent Technologies National Customer Care Center at 800-628-2888.
Show more

60 Read more

PARTNER Advanced Communications System Release 1.0 Programming and Use

PARTNER Advanced Communications System Release 1.0 Programming and Use

Off-Premises Range Extender (OPRE) allows you to connect a standard touch-tone phone beyond 3,000 feet (915 meters) in another building on the same continuous property. It also allows you to use a special circuit from your local phone company to provide off-premises station capability. Electromagnetic Interference (EMI) filters allow you to block “noise” generated by a nearby radio station, as well as most electrical devices. Caller ID devices allow you to store and process Caller ID information. Although the system provides functionally integrated, multi-line Caller ID on system display phones, you can connect other devices provided you subscribe to the service from your local phone company and connect the device directly to the Caller ID line. You cannot install a Caller ID device directly to a PARTNER extension jack or to a combination extension jack. Refer to “Connecting Caller ID Devices” in the PARTNER Advanced Communications System Installation guide for installation details. To order auxiliary equipment, refer to “Product Ordering Information” in Appendix B.
Show more

365 Read more

PARTNER Advanced Communications System Quick Reference Guide

PARTNER Advanced Communications System Quick Reference Guide

At pooled extensions, with Automatic Line Selection at its factory setting, the system first searches to find an available line in the main pool (pool 880 button 1, then button 2). If all outside lines in the pool are busy, the system selects an idle intercom line. However, you can change the order to accommodate a different automatic line selection. For example, your boss prefers her individual line (line 15) to be selected when she lifts the handset; then she wants auxiliary pool 881 to be selected, which is used for making international calls. To do this, set Automatic Line Selection to “15, 881, Intercom.”
Show more

112 Read more

PARTNER Plus Communications System Release 2 Installation and Use

PARTNER Plus Communications System Release 2 Installation and Use

A conference call connects up to five parties (including the originator) in a single call. You can connect both outside calls and intercom calls in a conference call, but the call cannot include more than two outside parties. You cannot have two outside calls in a conference call if your system is programmed for Outside Conference Denial (#109); see Chapter 3 for details. You can use System Speed Dial, Personal Speed Dial, or Auto Dial numbers to add calls to the conference. Do not add a busy or ringing outside call to a conference; if you do, all callers hear the busy or ringing signal. If you hear a busy signal when you are setting up a second call, or if the second party does not answer, reconnect with the held party by pressing the [Line] button. You cannot join a conference call: the origina- tor must add each party to the conference.
Show more

118 Read more

PARTNER™ Plus Communications System Installation and Programming Guide

PARTNER™ Plus Communications System Installation and Programming Guide

may send a special signal to the PARTNER Plus system to free the line. There are two possible signals: a long signal (450 milliseconds) used by most tele- phone companies, or a short signal (50 milliseconds) used by a few telephone companies. The length of the signal is called the hold disconnect time. If you put a line on hold and the call doesn’t “go away” within a minute or two after the caller hangs up, use this procedure to change the hold disconnect time.

87 Read more

PARTNER Advanced Communications System Release 1.0 System Planner

PARTNER Advanced Communications System Release 1.0 System Planner

By default, a transferred call returns to the originating extension if the call is not picked up. To specify a different transfer return extension, write the extension number in this column. For extensions to which you are connecting a PARTNER MAIL system, PARTNER MAIL VS system, or auto attendant, indicate a transfer return extension—usually extension 10—where a person can pick up calls that are transferred by the VMS or AA extension but not answered.

38 Read more

PARTNER Voice Messaging PC Card For the PARTNER Advanced Communications System

PARTNER Voice Messaging PC Card For the PARTNER Advanced Communications System

■ Automatic VMS Cover (#310): When the communications system Automatic VMS Cover feature is assigned for an extension, intercom and transferred callers are transferred to the voice messaging system when the called person does not answer by the fourth ring (or by the number of rings specified within the communications system VMS Cover Rings (#117) feature). The voice messaging system greets the caller with the general greeting. To leave a message, the caller selects the mailbox by dialing 1–4 or transfers to the receptionist by dialing [ 0 ].

47 Read more

PARTNER Communications System Release 4.1 Installation and Use

PARTNER Communications System Release 4.1 Installation and Use

programming and configuring your equipment to prevent unauthorized use. Your system manager should read all documents provided with this product to fully understand the features that can introduce the risk of toll fraud and the steps that can be taken to reduce that risk. AT&T does not warrant that this product is immune from or will prevent unauthorized use of common-carrier telecommunication services or facilities accessed through or connected to it. AT&T will not be responsible for any charges that result from such unauthorized use.

140 Read more

PARTNER Advanced Communications System Quick Reference Guide

PARTNER Advanced Communications System Quick Reference Guide

At pooled extensions, with Automatic Line Selection at its factory setting, the system first searches to find an available line in the main pool (pool 880 button 1, then button 2). If all outside lines in the pool are busy, the system selects an idle intercom line. However, you can change the order to accommodate a different automatic line selection. For example, your boss prefers her individual line (line 15) to be selected when she lifts the handset; then she wants auxiliary pool 881 to be selected, which is used for making international calls. To do this, set Automatic Line Selection to “15, 881, Intercom.”
Show more

106 Read more

PassageWay Administration for PARTNER Communications System Getting Started

PassageWay Administration for PARTNER Communications System Getting Started

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Show more

21 Read more

PARTNER Endeavor Communications System Programming and Use

PARTNER Endeavor Communications System Programming and Use

Key mode enables users to easily join calls since each line button can be labeled using a unique line number. For example, if you are requested to join a call on Line 2, you simply press the line button labeled “Line 2.” Key mode also lets users monitor call activity using the lights next to the line button—everyone who has a specific line assigned to their extension can tell when an incoming call is ringing on that line, when a call on that line is on hold, and when that line is in use. At installation, the system assigns outside lines to the buttons on all system phones from left to right, starting with the bottom row of buttons. On an extension basis, you can change which lines are assigned and which buttons are used to select the lines, if desired.
Show more

407 Read more

PARTNER II Communications System Programming and

PARTNER II Communications System Programming and

You will need to obtain four #12 screws of the appropriate type for the wall and weight of the carrier (a carrier with four 206 modules and a processor module weighs approximately 27.5 pounds or 12.3 kilograms.) You also need a length of #12 AWG or #14 AWG solid copper wire (not to exceed 25 feet) for grounding. In addition, if you need modular telephone cords for connecting the extension jacks on the control unit to the modular connecting blocks for extensions in the equipment room, short telephone cords for wall mounting MLS-model phones, or a 355A/355AF adapter and D8W telephone cord for connecting a call reporting device, order them before installation. Refer to “Product Ordering Information” in Appendix B of the PARTNER II Communications System Programming and Use guide for ordering instructions.
Show more

29 Read more

PARTNER® II Communications Systems PARTNER Plus Communications System Release 3.1 System Planner

PARTNER® II Communications Systems PARTNER Plus Communications System Release 3.1 System Planner

There are five pages to Form C—one page for each type of system phone and one page for Intercom Autodialers. Use Form C to record line assignments and to indicate programming for system telephone buttons that do not have lines assigned if the programming is to be performed from extension 10 or 11 during system installation. After installation, users can program additional features using the instructions in their Quick Reference cards.

30 Read more

PARTNER® II Communications System PARTNER Plus Communications System Release 4.0 System Planner

PARTNER® II Communications System PARTNER Plus Communications System Release 4.0 System Planner

There are five pages to Form C—one page for each type of system phone and one page for Intercom Autodialers. Use Form C to record line and pool button assignments and to indicate programming for system telephone buttons that do not have lines or pools assigned if the programming is to be performed from extension 10 or 11 during system installation. After installation, users can program additional features using the instructions in their Quick Reference booklets. A telephone button can be programmed as a line button (to access an outside line), as a pool button (to access a pool), as an Auto Dial button (to dial a phone number or a PBX/Centrex feature access code with one touch), or as a dial-code feature button (to access a dial-code feature with one touch). Line and pool buttons must have status lights; some features also require buttons with lights (see “Button Feature Summary”).
Show more

31 Read more

PARTNER Advanced Communications System 1600 DSL Module User Guide

PARTNER Advanced Communications System 1600 DSL Module User Guide

This chapter describes how to verify that the PARTNER ACS 1600 DSL module operates properly after installation. It also covers maintenance, and how to display the current configuration. Before you can test the voice capabilities of the PARTNER ACS 1600 DSL module, you must first provision it at the voice gateway.

213 Read more

PARTNER II Centrex Communications System Release 1 Installation and Use

PARTNER II Centrex Communications System Release 1 Installation and Use

controller and supply electrical power, the controller automatically assigns one Centrex line to each extension. The only exception is the phone connected to extension jack 10, which is assigned all of the lines in your system, to permit a receptionist to answer calls for users if they do not pick up immediately. (For more information on call coverage, see “Call Coverage Options” in Chapter 4.) By default, the primary line for an extension is set for immediate ringing and any secondary lines are set for delayed ringing. When a call comes in on a line, it rings immediately at the extension where the line is assigned as a primary line; after about 20 seconds it also begins to ring at any extensions where the line is assigned as a secondary line (for example, at the receptionist’s extension). NOTE:
Show more

166 Read more

PARTNER Advanced Communications System Quick Reference Guide

PARTNER Advanced Communications System Quick Reference Guide

Calling Group # 502 Group of extensions that can be called at the same time. Any user in the system can ring or page the entire Calling Group; the first extension to pick up the call is connected to the caller. This can be a useful feature for sales pools. Hunt Group # 505 Group of extensions among which calls are automatically distributed. A Hunt Group lets you off-load calls from a single user. You can assign user extensions to Hunt Groups 1 through 6. Use Hunt Group 7 for voice messaging extensions and Hunt Group 8 for fax calls. This can be useful for customer service groups. Night Service
Show more

116 Read more

PARTNER Communications System Release 4.0 Installation and Use

PARTNER Communications System Release 4.0 Installation and Use

While dialing restrictions are very effective, absolute protection against misuse cannot be guaranteed. System phones give you more protection against misuse than standard phones. Therefore, we strongly recommend that you install system phones where restricting phone use is important. Inside Only is useful for phones in reception areas or other public rooms where you want to prevent anyone using the phone from making outside calls. It is also useful for prohibiting calls from warehouse extensions, or from extensions that should be used only for receiving orders.

139 Read more

PARTNER Advanced Communications System Release 1.0 Installation

PARTNER Advanced Communications System Release 1.0 Installation

The next page shows a control unit with one PARTNER Advanced Communications System (ACS) processor module, two 206 modules and two 400 modules, giving the system a capacity of 15 outside lines and 20 extensions. Although your system may differ, this example will give you an idea of the types of equipment you can connect to it. In the example, system phones and industry-standard devices are connected to nine extensions. The circled numbers in the figure refer to items in the following list, which gives a brief description of the system’s components.
Show more

41 Read more

PARTNER Advanced Communications System Programming and Use

PARTNER Advanced Communications System Programming and Use

and extension capability. It has jacks for three outside lines and eight extensions. Using combinations of modules, you can have a maximum of 40 extensions with 15 lines (one ACS processor module and four 308EC modules) or 19 lines with eight extensions (one ACS processor module and four 400 modules). To get Caller ID, first you must subscribe to the service from your local phone company (if it is available) on a per-line basis, then connect those lines associated with Caller ID to the line jacks on the 206EC, 308EC, and/or 400EC modules. Any users with system display phones who receive calls on Caller ID lines will get Caller ID. For more information, see "Caller ID" on page 5-58.
Show more

466 Read more

Show all 10000 documents...