3D FEM
3D FEM comparison of lingual and labial orthodontics in en masse retraction
... loading. FEM is a mathematical method in which the shape of complex geometric objects and their physical properties are ...(3D) FEM models of the lower jaw and dentition, in order to map and compare ...
12
Design Optimization of Axial Flux Permanent Magnet (AFPM) Synchronous Machine Using 3D FEM Analysis
... This paper deals with the investigation of the behavior of a low speed, dual rotor- single coreless stator, axial flux permanent magnet synchronous machine for small power applications. Firstly, with the use of nonlinear ...
15
Modelling and Validation of 3D FEM for Laterally Loaded Single Pile
... (3D FEM) during design process to better understand ground mechanisms and soil-structure ...use 3D FEM to validate laterally loaded single pile ...studies, 3D FEM is in good ...
6
3D FEM Modeling and Technology of Piezoelectric Ring MEMS Antenna
... a 3D FEM properly designed tool. The used FEM tool analyzes this piezoelectric effect of the AlN layer through the stress relationships between the stress T, the strain S, electric field E, and ...
13
A Study on Evaluation of Seismic Response Considering Basemat Uplift with Soil-Structure Interaction Model by 3D-FEM
... (3D FEM) is one of the most effective methods in case of complicated ...using 3D FEM for the infinite half space soil medium and analysis results of dynamic response of NPP considering basemat ...
8
Fault rupture simulation of the 2014 Kamishiro fault nagano prefecture earthquake using 3D-FEM
... As the 1999 Chi-chi earthquake and the 1999 Kocaeli earthquake damaged many important structures due to surface rupture as well as a strong motions induced by the earthquake faults, displacement and inclination of ground ...
10
Developing a 3D FEM Model for Electromagnetic Analysis of an Axial Flux Permanent Magnet Machine
... method is time consuming. Numerical modeling is used in applications Such as design and optimization of electrical devices that accurate modeling is needed. In such applications, accuracy is very important and dura- tion ...
6
Comparison of Two Types of Dual Layer Generator in Field Assisted Mode Utilizing 3D-FEM and Experimental Verification
... Dual Layer Switched Reluctance Generator (DLSRG) The switched reluctance generator consists of two magnetically dependent stator and rotor layers, where each stator set includes twelve s[r] ...
17
3D FEM ANALYSIS OF EXTRUSION PROCESS OF AL2024-BERYL COMPOSITES
... Extrusion Process are now getting importance for its abilities to give improved mechanical properties, high production rate and less material waste when compared with that produced by machining, casting or by assembling ...
12
Simulation Analysis on Shaking Table Test of RC Box-type Shear Wall in Multi-axis Loading (H192)
... Nuclear Power Engineering Corporation (NUPEC) is carrying out a test project focused on multi-axes loading of RC shear walls, which is named 'Model Tests of Multi-Axes Loading on RC Shear Walls' and is sponsored by ...
8
Impact Angle Dependence of Erosive Wear for Spheroidal Carbide Cast Iron
... 2D FEM is too difficult to simulate impact particle with all kinds of shapes except axisymmetrical shapes, but 3D FEM has abilities to build impact particles with complex shapes so as to explain ...
6
Analyses of Reactor by 3D Nonlinear FEM Models Considering Basement Uplift for Simultaneous Horizontal and Vertical Ground Motions
... the 3D FEM soil model and to the lumped mass building model with a rigid basemat was ...the FEM soil model and that of the lumped mass models with SR soil springs calculated by the ...the FEM ...
8
A study on seismic behavior of nuclear power building in strong nonlinear area and fragility evaluation using 3 dimensional FEM Part-1 Ultimate seismic condition of building
... The 3D FEM model is shown in Figure 1(b). Because the buildings have a virtually symmetric shape around the central plane along the horizontal shaking direction, a half model with the symmetry plane is ...
10
Analysis of 3D Random Al18B4O33 Whisker Reinforced Mg Composite Using FEM and Random Sequential Adsorption
... studies showed the capability and advantage of FE analysis in the simulation of composite materials, not only for predicting the effective modulus, but also for the local field character- ization and overall stress-strain ...
5
Development of Ku Compact Broadband 1x4, 1x8 and 1x16 Power Dividers with SIW Optimized Chamfered Bends
... Abstract In this paper, compact broadband 1×4, 1×8 and 1x16 SIW power dividers based on SIW chamfered right bend operating in Ku-band frequency and that provide equal power split in all output ports are presented. ...
10
A 3D elasto-plastic FEM program developed for reservoir Geomechanics simulations: Introduction and case studies
... As a subsequent study to a recent one on elastic analysis of geomaterial, this study investigated the elaso-plastic behaviour of geomaterials. A 3D FEM code was developed for elasto- plasticanalysis, which ...
10
A Study on Applicability of Soil FEM Model to Evaluate Uplift Behaviour of NPP Buildings against Large Earthquake
... Fig. 1 shows the flowchart used in the current design method for estimating the seismic response of buildings in accordance with the level of basemat uplift. With decreasing ! , induced vertical motion occurs due to ...
10
AN INTUITIVE SOFTWARE SYSTEM FOR THE MODELLING OF THREE-DIMENSIONAL FEM TAPPING SIMULATIONS
... of 3D FEM simulations for the tapping process is the unacceptably high computing time due to the complex tool geometry, since the entire chamfer length of the tapping tool has to be considered to acquire a ...
26
III. TYPES OF FEM MODELS, CREATION OF THEM AND RESULTS A. 2D FEM model A.1 Properties of the FEM model
... There are bending and torsional shapes of custom vibration and that because of entering the third dimension into the FEM model. But we can find here also the interactive shapes of vibration between the structure ...
5
Paper 01-2015-2
... Рад уводи нови проблемски оријентисани језик FORTU, који омогућава инжењерима да лако развију различите методе за дизајн и анализу нестандардних механичких конструкција. Примењен је у FORTU-FEM CAD систему, чија ...
9