AISI 1045 steel
To Study the Effect of Process Parameters for Minimum Surface Roughness of Cylindrical Grinded AISI 1045 Steel
... study AISI 1045 steel has been selected as the test material because it is an important material used for making axles, bolts, connecting rods, pins spindles, crank shaft, guide rods ...
6
Increasing Surface Hardness of AISI 1045 Steel by AIH FPP/Plasma Nitriding Treatment
... of AISI 1045 steel, a new hybrid surface modi fi cation; combination of atmospheric-controlled induction-heating fi ne particle peening (AIH-FPP) and plasma nitriding, was ...of AISI 1045 ...
6
Optimum Swept Angle Estimation based on the Specific Cutting Energy in Milling AISI 1045 Steel Alloy
... In this study, a new optimized value at which ploughing effects are minimal was developed. The values correspond to milling at swept angle of between 31.57 o to 31.8 o and at 0.19 mm/tooth feed. These values were derived ...
6
Effect of Contact Configuration on the Tribological Performance of Micro Textured AISI 1045 Steel under Oscillating Conditions
... The tribological performance of micro-textured AISI 1045 steel was investigated by an oscillating test. This study compared two contact schemes: (1) ball-on-disk and (2) line contact con fi guration. ...
8
Investigation into the Effect of EDM Parameters on Tool Wear Rate during Machining Of AISI-1045 Steel
... The effect of machining parameters on AISI 1045 steel has not been fully explored. A study of TWR during EDM process on this material will be quite useful. In the present work design of experiments ...
12
Experimental Analysis of Cutting Forces and Temperature in Orthogonal Machining of AISI 1045 Steel
... In the present investigation, work piece selection is a preliminary step which involves the selection of type (rod or tube), outer diameter, length, and tube thickness. End turning of the tube is the simplest and the ...
7
PARAMETER OPTIMIZATION WHILE DRY TURNING AISI 1045 STEEL USING CBN TOOL BY RESPONSE SURFACE METHODOLOGY
... Dry machining is a machining process without coolant and it is more popular as a finishing process. The purpose of this research project is to optimize the parameters using Response Surface Methodology when dry turning ...
14
Duplex Surface Treatment of AISI 1045 Steel via Plasma Nitriding of Titanized Layer
... In this study, surface of medium carbon steel (AISI 1045) was modified by titanizing followed by plasma nitriding. Titanizing was performed using pack cementation method, in a pack mixture of ...
6
Finite element simulation of machining aisi 1045 steel using uncoated carbide tool
... turning AISI 4340 steel with uncoated carbide tool (SNMM ...carbon steel AISI 1040 using a venture to mix compressed air (the air pressure was of ...
39
THE INFLUENCE OF THE CONDITIONS OF EMULSION MIST FORMATION ON THE SURFACE ROUGHNESS OF AISI 1045 STEEL AFTER FINISH TURNING
... 5. Maruda R.W., Krolczyk G.M., Feldshtein E., Pusavec F., Szydlowski M., Legutko S., Sobczak- Kupiec A., A study on droplets sizes, their distribu- tion and heat exchange for minimum quantity cool- Fig. 5. Some results ...
6
IMPACT OF COMPRESSED AIR PRESSURE ON GEOMETRIC STRUCTURE OF AISI 1045 STEEL SURFACE AFTER TURNING WITH THE USE OF MQCL METHOD
... 6. Hafenbraedl D., Malkin S. Technology environ- mentally correct for intern cylindrical grinding. Fig. 4. Abbot-Firestone curves for 1045 carbon steel after turning with the use of MQCL method with ...
5
Surface Integrity Of AISI 1045 Steel When Machined With TiC Cutting Tool
... high-carbon steel, high-carbon speed steel, cobalt matrix and solid carbides to cemented or sintered carbides, ceramics and special cutting tools such as titanium nitride, titanium carbide and many ...
24
Effect of Bath Parameters on Electroless Ni-P and Zn-P Deposition on 1045 Steel Substrate
... increased, this can be attributed to the stability of the process. Electroless plating depends strongly on the stability of the bath. This is of importance in industries where plating is done for decorative purpose; a ...
14
IJRTSM INTERNATIONAL JOURNAL OF RECENT TECHNOLOGY SCIENCE & MANAGEMENT OPTIMIZATION OF CUTTING PARAMETERS FOR TURNING OPERATION IN CNC LATHE FOR AISI 1045 MATERIAL USING TAGUCHI METHOD AND ANOVA METHOD BY EXCEL 2007 SOFTWARE Sachin Tripathi 1, Rajeev Dwivedi2 Neeraj Nagayach 3
... The main purpose of today’s manufacturing industries is to produce low cost, high quality products in short time. They mainly focused on achieving high quality, in term of part accuracy, surface finish, high production ...
10
Fretting wear characteristics of AISI 1040 steel alloy
... With the increase in sliding amplitude, keeping normal load constant, the transition from partial slip to gross slip takes place. Li & Lu, (2013) performed fretting wear test on Inconel 600 alloy and concluded that ...
9
ANALYSIS OF SURFACE ROUGHNESS MILLED OF STEEL AISI 1045 USING X-BAR AND R CONTROL CHART
... The steel milling AISI 1045 has been gaining prominence in industry in recent years as it allows machined parts to be obtained with low-cost ...of AISI 1045 steel using titanium ...
9
Investigation Of Surface Integrity When Machining AISI 1045 Using Uncoated Carbide Cutting Tools
... Figure 4.6 shows both results of surface roughness in wet and dry condition at feed rate 0.50mm/rev. From the graph it shows that as the feed rate increase, dry cutting better than wet cutting, this situation occurs ...
81
Investigation Of Tool Wear When Machining AISI 1045 Using Uncoated Carbide Cutting Tool
... machining, AISI 1045 considered as medium carbon steel that widely used in manufacturing industries, especially in automotive because of its mechanical behaviour such as good machinability, high ...
24
The Preparation of the Chromized Coatings on AISI 1045 Carbon Steel Plate with the Electroplating Pretreatment of Ni or Ni/Cr-C Film
... of 1045-Ni-CrC-Cr(700-2) for 1 h exhibits a low stable value of ...that 1045-Ni-CrC-Cr(700-2) is stable under the cathode ...of 1045-Ni-Cr(700-2) increases gradually with time after the testing time ...
15
Experimental Investigation of PMEDM on AISI 1045
... process. AISI 1045 steel is medium tensile steel which is supplied in the black hot rolled or it can be in normalized ...of AISI 1045 is 570 - 700 MPa and Brinell hardness ...
6