• No results found

channel geometry

Deriving Shape Functions For 8-Noded
Rectangular Serendipity Element in
Horizontal Channel Geometry and Verified

Deriving Shape Functions For 8-Noded Rectangular Serendipity Element in Horizontal Channel Geometry and Verified

... Abstract — In this paper, I derived shape functions for 8-noded rectangular serendipity element in horizontal channel geometry and also I verified two verification conditions for shape functions. First ...

6

Effects of tides and surface runoff on channel geometry

Effects of tides and surface runoff on channel geometry

... of channel that experiences flood problem due to heavy rainfall and tide ...the channel reach shall be evaluated to determine the dominant energy from either upstream boundary condition or downstream ...

21

Quantifying the combined effects of multiple extreme floods on river channel geometry and on flood hazards

Quantifying the combined effects of multiple extreme floods on river channel geometry and on flood hazards

... 82 This study aims to evaluate sediment dynamics within a river channel during a repeated series of 83 extreme floods, and the resultant changes in channel geometry, conveyance capacity [r] ...

29

A Sticky Pursuit Of The Threshold Channel: The Effect Of Cohesion On Alluvial River Channel Geometry

A Sticky Pursuit Of The Threshold Channel: The Effect Of Cohesion On Alluvial River Channel Geometry

... hydraulic geometry of fine-grained (sand-bedded and mud-bedded) alluvial river chan- ...stable channel geometry are, respec- tively, indicative of a common mechanism and balanced forces, I started ...

124

Trends in alluvial channel geometry and streamflow : an investigation of patterns and controls

Trends in alluvial channel geometry and streamflow : an investigation of patterns and controls

... in channel geometry are quantified by subtraction of repeatedly digitised ...in channel width and/or vegetation ...quantify channel change over ‘hyperscale’ time periods, ...

246

Effect of micro-channel geometry on fluid flow and mixing

Effect of micro-channel geometry on fluid flow and mixing

... of geometry, therefore only one fluid with similar viscosity was used in these ...the channel geometry when other parameters such as fluid inlet velocity, viscosity and pressure of fluids were kept ...

15

Diffusion limited aggregation in channel geometry

Diffusion limited aggregation in channel geometry

... Diffusion-limited aggregation (DLA) has attracted considerable attention since its introduction by Witten and Sander in 1981 [1]. In this model an aggregate or cluster grows by capturing diffusing particles which irre- ...

5

Effect of micro-channel geometry on fluid flow and mixing

Effect of micro-channel geometry on fluid flow and mixing

... Permanent repository link: http://openaccess.city.ac.uk/14582/ Link to published version: http://dx.doi.org/10.1016/j.simpat.2010.12.008 Copyright and reuse: City Research Online aims to[r] ...

6

Leaf venation, as a resistor, to optimize a switchable IR absorber

Leaf venation, as a resistor, to optimize a switchable IR absorber

... Material channel resistor ...resistance channel. If we assume that we know R0 the aim is to design the channel geometry to give equal flow rates through all the ...longitudinal channel ...

16

Analysis of flow through rectangular mini channel with surface irregularities

Analysis of flow through rectangular mini channel with surface irregularities

... of channel dimension and geometry (ii) critical Reynolds number and (iii) correlations in terms of fluid properties and micro-channel ...sectional geometry of channels, the effects of which are ...

6

The Effect of cylindrical obstructions on the fluid flow in narrow rectangular channels

The Effect of cylindrical obstructions on the fluid flow in narrow rectangular channels

... LIST OF FIGURES Figure Page 1-1 TYPICAL CHANNEL GEOMETRY FOR PCR DETECTION CHAMBER 4 1-2 TYPICAL HELE-SHAW GEOMETRY 7 1-3 FLUID FLOW PATTERN FOR HELE-SHAW CELL 8 1-4 PCR DETECTION POUCH [r] ...

156

Workability study in near-pritectic Sn-5%Sb lead-free solder alloy processed by severe plastic deformation

Workability study in near-pritectic Sn-5%Sb lead-free solder alloy processed by severe plastic deformation

... Abstract: Severe Plastic Deformation (SPD) of Sn-5Sb solder alloy was carried out under different deformation conditions including the temperature range of 298, 330, 360, 400 K and die designs in the present research. An ...

13

Leaf venation, as a resistor, to optimize a switchable IR absorber

Leaf venation, as a resistor, to optimize a switchable IR absorber

... Material channel resistor ...resistance channel. If we assume that we know R0 the aim is to design the channel geometry to give equal flow rates through all the ...longitudinal channel ...

17

A Review On Enhancement Of Heat Transfer In Microchannel Heat Exchanger

A Review On Enhancement Of Heat Transfer In Microchannel Heat Exchanger

... This review paper is comprehensive study of heat transfer in micro-channel heat exchanger. In this study we have demonstrated research based result and outcomes without any assumptions. In this paper we have ...

7

Positive Impact Program Evaluation

Positive Impact Program Evaluation

... the channel form no longer undergoes progressive adjustments, such as with bed and bank erosion, and it is essentially in a state of dynamic equilibrium (Wolman, 1967; Schumm, 1977; Henshaw and Booth, 2000; ...

74

A Numerical Study On Effects Of Microchannel Shape To Condensation Of Steam

A Numerical Study On Effects Of Microchannel Shape To Condensation Of Steam

... From the literature review above, studies on the condensation process in microchannel are not yet well established, particularly in numerical simulations for the channel geometry. So it is essential to ...

5

On investigating the flow through an axisymmetric channel with sudden changes in geometry

On investigating the flow through an axisymmetric channel with sudden changes in geometry

... the channel geometry, the contraction and expansion ratio, the sharpness of the throat in the channel, the velocity profile imposed at the inlet of the expansion as well as the Reynolds number could ...

6

Deriving principal channel metrics from bank and long-profile geometry with the R package cmgo

Deriving principal channel metrics from bank and long-profile geometry with the R package cmgo

... examining channel metrics in a quantitative and objective ...cross-section geometry is required to model local flow hydraulics, which in turn determine erosion and thus channel dynam- ...Similarly, ...

14

Process Modelling of Equal Channel Angular Pressing for Ultrafine Grained Materials

Process Modelling of Equal Channel Angular Pressing for Ultrafine Grained Materials

... the geometry and material properties on the deformation behaviour of the workpiece during ECAP, isothermal two- dimensional plane-strain finite element method (FEM) simulations for the ECAP process have been ...

5

Principal Longevity, Leadership Behaviors, and Student Academic Achievement

Principal Longevity, Leadership Behaviors, and Student Academic Achievement

... hydraulic geometry and bedforms are observed in the Middle Saluda ...in channel morphology appear to be associated with a key transition zone (Sections ...on channel morphology is evident at site 8, ...

86

Show all 10000 documents...

Related subjects