Compressor blade
Fatigue Life Estimation of Compressor Blade of Engine
... of compressor blade, Pro-E is used for design of solid model and ANSYS software for analysis for model generated, by applying boundary condition, also includes specific post processing and life assessment ...
6
Life Estimate of a Compressor Blade through Fractography
... Failure analysis of fractured components provides some information about the causes and conditions of fracture. Fractography is an indispensable part of the failure analysis as it is usually the only means by which the ...
8
Form finding as a modelling tool for shaping mechanical components: a feasibility case study of an axial flow compressor blade
... axial-flow, compressor blade as a case ...a compressor blade. The blade shapes obtained by this method correspond, in the first instance, to a minimal form and, subsequently, a minimal ...
16
A real parametric characterisation of ex service compressor blade leading edges
... Surface metrology in the form of a single line or ‘ pro fi le ’ of surface point heights (and associated parameters) often acquired by a contact stylus instrument is widely understood and employed [3]. Areal surface ...
8
Evaluation of Material Data to the Numerical Strain-Life Analysis of the Compressor Blade Subjected to Resonance Vibrations
... This paper presents the impact of selecting the fatigue material model on the numerically determined fatigue life of a compressor blade. In the work, the first stage compressor blade of the ...
7
Influence of microstructure and inclusions on very high cycle fatigue behavior of compressor blade steels
... centrifugal compressor is typical gas delivery equipment which plays an important role in energy, petroleum, chemical, and other important ...of compressor blades may be high cycle fatigue induced by wake ...
8
Computational Analysis of Compressor Blade
... in compressor blade design is essential. Generating qualified blade profiles is a prerequisite to developing high-performance ...a compressor blade in CATIA. after finish the ...
8
Presenting Three Design Methods for Axial Compressor Blade via Optimization
... a blade in addition to high flexibility with the least number of ...the compressor blade, due to a rise in the negative pressure gradient, the value of minimum drop increases and the gradient of drop ...
14
Static fracture and modal analysis simulation of a gas turbine compressor blade and bladed disk system
... aero-turbine compressor blade subjected to resonant ...turbine compressor blade, while using the Paris and Forman-Newman-De Koning model to predict fatigue ...turbine blade assumed as a ...
23
Optimization and Vibration Analysis of Compressor Blade with Different Blade Angle
... a compressor blade of different ...of blade angle profiles of the compressor blade with angle ...the compressor blade was ...
12
Transition induced by linear and nonlinear perturbation growth in flow past a compressor blade
... 65 blade geometry, adverse pressure gradient and separation are observed on most of the blade surface except the leading edge on the suction surface and trailing edge on the pressure surface (Zaki et ...
29
An Outrun Competition of Corrosion Fatigue and Stress Corrosion Cracking on Crack Initiation in a Compressor Blade
... broken blade indicate that the pits join together and make one bigger pit under SCC mechanism which reduces the failure ...the blade under existing forces are analyzed by ABAQUS ...
8
Fatigue and Fretting Studies of Gas Compressor Blade Roots
... GEOMETRICAL MODELLING: In this study the dovetail blade-disc region geometry has referred from [1] and [2], with respect to those designs geometrical models were created in CATIA V5 R20 Cad software. For 20 0 skew ...
5
Investigate Blade Failure In Axial Compressor
... axial compressor were designed by arranging thickness distribution around a camber ...flow compressor blade, based on understanding the flow behaviors in the blades, where stacking lines of the ...
24
Experimental Investigation of the Compressor Cascade under an Active Flow Control
... through compressor blade cascades, under higher loading at higher angle of attack, tends to ...two-dimensional blade cascades, ...the blade, at a vicinity of the flow separation, namely at ...
6
Effect of blade profile on the performance characteristics of axial compressor in design condition
... Streamline curvature method (SCM) is widely used for quasi-three-dimensional design of an axial compressor blade. SCM is utilized primarily for an inviscid flow. In fact, it offers a flexible method of ...
10
Study on compressor performance with the orifice shape of a compressor suction valve
... Figure-11 shows the cooling capacity (CC) and compressor work (CW), and energy efficiency ratio (EER) according to the number of suction orifices. Cooling capacity is the largest in case 3, but little difference ...
5
Turbulent flow phenomena and boundary layer transition at the circular arc leading edge of an axial compressor stator blade
... of compressor blades react to changes in engine operating points in a steady and unsteady environment is ...stator blade with a circular arc leading edge ...2D compressor cascade at Reynolds numbers ...
196
Computational fluid dynamics simulations of blade damage effect on the performance of a transonic axial compressor near stall
... the blade so that the incidence increases on the blade on the right hand side and decreases on the blade on the left hand side, in the rotating frame of ...
44
Use of pressure spectral maps for analysis of influence of the plenum volume on the surge in centrifugal blower
... pumps [19, 20]. Kryłłowicz [21] stated that the inlet recirculation was also characteristic for centrifugal compressor units with semi-open impellers. The phenomenon was described as a torus shaped vortex which ...
10