finite-element-analysis model
Analysis on the Buckling Behavior of the Spacer Grid Structure for the PWR Fuel Assembly
... In addition, the finite element analysis model is in good agreement with the impact test results, therefore this finite element model and the analysis procedure will be [r] ...
8
Seismic analysis of the nuclear reactor vessel and internals with using model reduction method
... experiments, finite element analysis model of totally assembled reactor was constructed as shown in Figure ...Fluid80 element, which is the displacement-based ...
11
Finite Element Of Human Spine CAD Model Analysis
... Finite Element is the best method can be used to visualize stress distribution on the lumbar ...The finite element method of numerical analysis has enabled researchers to solve many ...
24
FINITE ELEMENT ANLYSIS OF EVALUATION OF RADIAL STRESSES IN HYDRO - ASSISTED DEEP DRAWING PROCESS
... CFD analysis is used to determination of fluid pressure with given punch speeds at radius using castor ...The element type is fluid 141 elements from flotran CFD library is selected for ...The ...
10
Finite element model of the bed
... parametric model is sufficiently complex for realization of optimization ana- lysis of ...this analysis extended investigation of verification of mechanical material properties, which are taking into ...
6
DESIGN IMPROVEMENT AND ANALYSIS OF TRACTOR TROLLEY AXLE BY USING CAD/CAM/CAE TECHNIQUES
... work finite element analysis approach is used to modify existing rear axle of tractor ...axle finite element model was predicted after the dynamic load was imposed on ...For ...
10
DYNAMIC ANALYSIS AND STRUCTURAL DESIGN OF TURBO GENERATOR FRAME FOUNDATION – A REVIEW
... static analysis and dynamic analysis of turbine reinforced concrete foundations and also focuses on the load cases to be applied for ...complex finite element model was constructed to ...
6
Finite element model of a double-stage helical gear reduction.
... ANSYS model was built using BEAM188, MASS21, COMBIN14, and MATRIX27 ...beam element for 3D analysis. MASS21 is a structural mass point element also suitable for 3D ...per element w ith ...
117
Finite-element model and modal analysis of grand piano soundboard
... Parametricky je určena geometrie desky (vnější tvar hrany desky, proměnlivá tloušťka desky) a rovněž skladba desky z přířezů (orientace a šířka přířezů). Tvar modelu desky i skladbu desky z rezonančních přířezů ilustruje ...
8
Original Article Three-dimensional finite element stress analysis on non-bridge external fixation to distal radius fracture
... the finite element anal- ysis method to discuss the stress distribution and displacement conditions of the DRF model fixed by AO NBEF under the four operating con- ...radius model, the ...
7
MULTIBODY DYNAMIC ANALYSIS AND SIMULATION OF ENGINE MODEL
... HyperView is a complete post-processing and visualization environment for finite element analysis (FEA), multi-body system simulation, video and engineering data. The contour plot for displacement of ...
9
Finite Element Analysis of an In Vitro Traumatic Joint Loading Model
... this model because the threshold at which cells remain viable depends on strain rate, impact load duration and integrity of the ...this model, so peak forces may have been higher due to the strain rate ...
182
Finite Element Analysis Of Bridge Cranes’ Proof Load Test Data
... as Finite Element Analysis) could go a long way to improve cranes performance and minimize ...6- Element model of the Finite Element Method was used in analyzing the proof ...
16
Finite element analysis of mechanical properties for 2D woven Kenaf composite
... The model approximately 52000 finite elements and 12000 nodes was generated using the finite element analysis software for modeling and mechanical analysis based on the 8-node ...
36
Finite Element Analysis of High Pressure Composite Vessels
... H. Medhavi Sinha et. al. have done her investigation, the limited component model of CFRP, tube shaped composite weight vessel is built up utilizing limited component programming ANSYS 11. The models got for ...
12
Thermal Stress Analysis of a Dam Wall by Finite Element Model
... related analysis are cited below. Abdullah et al. [1] used a 3D finite element model to perform coupled thermo-structural analysis on gravity ...dimensional finite element ...
7
ANALYSIS OF FULL LENGTH FINITE ELEMENT MODEL OF PROFILE AND TWISTED ENDODONTIC FILES
... file model is more flexible than the Twisted file is more elastic than ProFile model, hence it allows dentist to operate with more ease in curved canals during the process of final ...
10
Quasi-Static and Dynamic Behaviors of Helical Gear System with Manufacturing Errors
... LTCA model based on sub-structure technique and elastic contact theory to determine TVMS, LSTE and LCMS of helical gears hav- ing manufacturing ...This model provides sufficient precision and high ...
9
DYNAMIC ANALYSIS AND STRUCTURAL DESIGN OF TURBO GENERATOR FOUNDATION
... static analysis and dynamic analysis of turbine reinforced concrete foundations and also focuses on the load cases to be applied for ...complex finite element model was constructed to ...
10
A new method for the treatment of unilateral posterior cross-bite: a three-dimensional finite element stress analysis study
... RME model in computer environment by using Rhinoceros ...RME model was transferred to com- puter, it was placed onto the occlusal surfaces of the maxillary ...
9