• No results found

FEA method

Analysis of a Sponge Rubber using FEA Method

Analysis of a Sponge Rubber using FEA Method

... Abstract: The thesis defines design and development of a Pressure Actuation Mechanism for land based munitions. This mechanism employs rubber pads for actuation. A consistent and effective rubber compound needs to be ...

5

Effect of Stress Distribution on Transverse and Longitudinal Framing in Cargo Ship using FEA Method

Effect of Stress Distribution on Transverse and Longitudinal Framing in Cargo Ship using FEA Method

... Abstract: A cargo ship’s hull is made up of bent plates that are not stiffened. The hull can be strengthened by the structural member of the transverse or longitudinal framing system. Frames are strengths member that ...

7

Optimization Of Front Axle For Heavy Commercial Vehicle By Analytical And FEA Method

Optimization Of Front Axle For Heavy Commercial Vehicle By Analytical And FEA Method

... wheel. Front axle carries the weight of the front part of automobile as well facilitates steering and absorb shock due to road surface variations. So, proper design and optimization of front axle is extremely crucial to ...

7

DESIGN & STATIC ANALYSIS OF LEAF SPRING USING FEA METHOD BY ANSYS

DESIGN & STATIC ANALYSIS OF LEAF SPRING USING FEA METHOD BY ANSYS

... 5. M. Raghavedra , Syed Altaf Hussain , V. Pandurangadu and K. PalaniKumar, “Modeling and Analysis of Laminated Composite Leaf Spring under the Static Load Condition by using FEA”, International Journal of Modern ...

7

Thermal Analysis of Corrugated Plate Heat Exchanger by using Ansys Software through FEA Method

Thermal Analysis of Corrugated Plate Heat Exchanger by using Ansys Software through FEA Method

... a counter flow corrugated plate heat exchanger were investigated through an experiment by Shive Dayal Pandey and V. K. Nema. It had been discovered that the heat transfer characteristics improve with the decrease in ...

11

Design Thermal and Structural Analysis of Piston Using Composite Materials by Fea Method

Design Thermal and Structural Analysis of Piston Using Composite Materials by Fea Method

... The software uses the Finite Element Method (FEM). FEM is a numerical technique for analyzing engineering designs. FEM is accepted as the standard analysis method due to its generality and suitability for ...

11

DESIGN AND ANALYSIS OF TVS BIKE FRAME USING FEA METHOD

DESIGN AND ANALYSIS OF TVS BIKE FRAME USING FEA METHOD

... This chapter will describe all the processes that involved in the dynamic analysis structure of motorcycles chassis. For structural analysis, it consist two methods which are finite element analysis and modal analysis ...

6

Design Thermal and Structural Analysis of Piston Using Composite Materials by Fea Method

Design Thermal and Structural Analysis of Piston Using Composite Materials by Fea Method

... In order to improve the wear performance, a metal based insert is reinforced with the base alloy. Cast iron and steel inserts normally reinforced with the light weight alloy during the casting process. To achieve the ...

10

Design Static and Dynamic Analysis and Weight Optimization of Car Chassis by Using Fea Method

Design Static and Dynamic Analysis and Weight Optimization of Car Chassis by Using Fea Method

... With respect to monolog chassis, most bleeding edge cars nowadays utilize this kind of suspension. A monolog case is an unmarried bit of structure that offers shape to the car. A one-piece chassis is built by ...

15

Thermal Analysis of Corrugated Plate Heat Exchanger by using Ansys Software through FEA Method

Thermal Analysis of Corrugated Plate Heat Exchanger by using Ansys Software through FEA Method

... a counter flow corrugated plate heat exchanger were investigated through an experiment by Shive Dayal Pandey and V. K. Nema. It had been discovered that the heat transfer characteristics improve with the decrease in ...

11

THERMAL ANALYSIS OF CAR BRAKE ROTOR BY USING FEA METHOD

THERMAL ANALYSIS OF CAR BRAKE ROTOR BY USING FEA METHOD

... The disc brake rotor is a rotating device. Braking is a process which converts the kinetic energy of the vehicle into mechanical energy which must be dissipated in the form of heat. This paper presents the analysis of ...

10

Analysis of Four Wheel Steer Electronic Vehicle Using FEA Method

Analysis of Four Wheel Steer Electronic Vehicle Using FEA Method

... Abstract:-we are moving towards the future development, then we are to improve our technology. The next step towards the technical development is in automotive sector.This is possible by creativity, designing and ...

8

Design and Weight optimization of Pinion by using FEA Method

Design and Weight optimization of Pinion by using FEA Method

... Mr. Kishor N. Naik, Prof. Dhananjay Dolas, [3] The main objective of this paper is to analyze the bending stresses occur on the gear tooth profile of gear used in gear box of special purpose machine also effect on ...

8

The Strength of the Bus Structure with the Determination of Critical Points

The Strength of the Bus Structure with the Determination of Critical Points

... A monocock structure of an airport bus is a very demanding product as regards its strength. With the application of the FEA (Finite Element Analysis ) method the allegedly critical points of the framework ...

7

Study of different stresses induced in rotor
shaft of electric motor

Study of different stresses induced in rotor shaft of electric motor

... The motor rotor shaft is designed on the basis static and dynamic loadings. The design is validated analytically for static case and pattern is observed for dynamic case. As expected in dynamic loading stresses induced ...

9

Analysis of the relation between organic products consumption and box schemes use in Alicante (Spain)

Analysis of the relation between organic products consumption and box schemes use in Alicante (Spain)

... The first group of variables, consisting of three factors (which explain a total variance of 63.95%), refer to val- ued attributes in fruit and vegetables. The first factor, “product composition” includes attributes such ...

6

Analysis of air flow in the mouthguard design by using CFD approach

Analysis of air flow in the mouthguard design by using CFD approach

... numerical method to analyze the statics and dynamics properties of the mechanical part such as deformation, stress of the structure, flow of gases using CFD techniques and many more to solve complex structure in ...

5

Comparison of Intrusion of Maxillary Incisors using Three-Piece Intrusion Arch and Skeletal Anchorage: A Finite Element study

Comparison of Intrusion of Maxillary Incisors using Three-Piece Intrusion Arch and Skeletal Anchorage: A Finite Element study

... Del Castillo McGrath M. G et al (2018) 29 evaluated by means of the finite element method, initial tooth displacement and periodontal stress distribution using various mandibular anterior intrusion mechanics using ...

106

A Dynamic Temperature Controlling Method for Processors in Constrained Sealed Spaces

A Dynamic Temperature Controlling Method for Processors in Constrained Sealed Spaces

... In the following three experiments, we use ANSYS to calculate the temperature values of the die. We do not compare them with on-site measured values due to the following reasons. First, there is no suitable method ...

6

Investigation into residual stress effects on apparent fracture toughness of high, medium and very low constraint geometries

Investigation into residual stress effects on apparent fracture toughness of high, medium and very low constraint geometries

... As can be seen taking this approach to presenting the test results provides a better description of what has physically happened in the testing. There can be see a reduction in all percentiles of failure probability ...

11

Show all 10000 documents...

Related subjects