[PDF] Top 20 ND-45504 (E) ISSUE 2 PART OF STOCK # 151900 Circuit Card Manual

... AP00 card can not recognize the actual state of the DCE, so that the call records or system messages will not be stored in the memory buffer on the AP00 card even if the cable is discon- nected from the ... See full document

... Any Multiline Terminal can be assigned as a CAT terminal through programming. The Multiline Terminal can still be used as a regular telephone when it is not in CAT mode. If the system is initialized by “C” (Resident ... See full document

... line/trunk circuit cards can be used as same as the main site, except the CSI card for wireless system according to UTAM ...application circuit cards cannot be used at the remote ...ILC card ... See full document

... Figure 4-11 shows sample cable connections, where HUB (PA-M96) cards are provided in a dual configu- ration and the FCH (PA-FCHA) card is located in PIM 1 (1-IMG system/IMG0). When HUB cards are pro- vided in a ... See full document

... 16. When using this feature, the user must assign Service Feature Restriction Class and Route Restriction Class, which are different from those of other stations to ports of CFTB circuit card, and also ... See full document

... AP00 card after data setting. : Commands that require a reset of the AP01 card after data ...DCH card after data setting. : Commands that require a reset of the DTI card after data ...DBM ... See full document

... • An equipment grounding conductor that is at least as large as the ungrounded branch- supply conductors is to be installed as part of the circuit that supplies the NEAX2000 IVS 2 . Bare, covered, or ... See full document

... The CPU sends diagnosis data at periodic intervals to the Port Microprocessor (PM) on FCH (PA-FCHA) cards to monitor the PM. If the CPU cannot receive the return data within a predetermined time, the system displays the ... See full document

... two circuit cards are ...(DTI) card is used to interface to the digital network, and satisfies the require- ments for ISDN Layer ...(DCH) card is used to transmit and receive D Channel signaling data ... See full document

... The maximum number of Wireless PS stations has been expanded from 168 to 250 when an Integrated type system is being used. Previously, each PS line reduced the capacity of CM10 by three ports [One port for CM1C and two ... See full document

... TSW card generates its base clock signals, and adjusts their phase with the source clock signals so the PLO can send the synchronized clock signals to the ...this circuit card provides --- PA-CK14 ... See full document

... An equipment grounding conductor that is at least as large as the ungrounded branch-supply conductors is to be installed as part of the circuit that supplies the NEAX2000 IVS. Bare, covered, or insulated ... See full document

... In the PBX, all line/trunk circuits are provided by installing the cards into a card shelf. The PBX employs a flexible port assignment architecture in which the system allocates a port (Time Slot) to each LEN ... See full document

... Series E Multiline Terminals (DTP-8-1, DTP-8D-1, DTP-16-1, DTP-16D-1, DTP-32-1, DTP-32D-1), the feature programming is available in same method as the Series III Multiline ...Series E Multiline Terminal ... See full document

... b.) When either (or both) of the lamps are OFF, initialize the circuit card, or perform the insertion/ extraction of the circuit card once or twice. Also, if a sub board is in use, make sure ... See full document

... If the switching system is operated in an environment that does not meet these specifications, the reliability of the switching equipment may be impaired. Improper operating conditions can cause circuit boards, ... See full document

... This circuit card provides the Attendant Consoles (ATTs) with information such as ATT call termination/answer/release (abandoned call) via the data link that is established in the TSW ...This circuit ... See full document

... 17. When using this feature, the user must assign Service Feature Restriction Class and Route Restriction Class, which are different from those of other stations to ports of CFTB circuit card, and also ... See full document

... line/trunk card control information to the associated peripheral circuits via IO ...a circuit card, the CPU identifies the cause of the fault, changes over the CPU so that system operation is not ... See full document

... this circuit card contains the audible tones, such as Dial Tone, Busy Tone, Ring Back Tone, ...this circuit card. Additionally, this circuit card provides the Voice Prompt ... See full document