[PDF] Top 20 ND-45669 (E) ISSUE 2 PART OF STOCK # 151901 Command Manual

... (2) If “7XX” (XX=20-83) is displayed when reading out the assigned data for the access code, the access code which was entered is the leading digit(s) of another access code consisting of more dig- its. Add a ... See full document

... The SYS-ID is a unique ID which was given to manage the PCS system. The area where the SYS-ID is effective is called PCS Community. Every PCS Community in a Fusion network is given a unique PHS Community Number (PCN). ... See full document

... Figure 2-9, even when Channel 1 through Channel 10 have been assigned by the sys- tem data programming (CM07 YY = 01) excepting Channel 5, the system allocates a total of 10 time slots for all the ten ... See full document

... Provides Memory, TDSW (1024CH x 1024CH), 16-line CFT, PB sender, Clock, PLO 2 ports (receiver mode/source mode), two RS-232C ports, 2-line DAT (Recording duration: Max. 128sec.), DK, 4-line PB receiver, ... See full document

... The CPU sends diagnosis data at periodic intervals to the Port Microprocessor (PM) on the FCH (PA-FCHA) cards to monitor the PM. If the CPU cannot receive the return data within a predetermined time, the system displays ... See full document

... A maximum of seven Tie Lines can participate in a conference when the associated trunks can receive an answer signal and a release signal from the distant switching system. On the other hand, in the case of a C.O. line, ... See full document

... Upon accepting a connection request and/or a service request from a terminal, this facility transfers the ID code of that specific terminal to the AP and also executes either connection processing or connection ... See full document

... 4. The maximum number of stations that can set the same wake-up time can be assigned as one of the following: 64, 128, 256, 512 stations per LP (Local Partition) depending on System Data programming. If the number of ... See full document

... Assign FCH routing data using the AFPC command. A maximum of 8 connection routes and FCHN/ FPCN can be assigned on a node basis. FCHN is used for Fusion System with FCH. FPCN is used for Fusion System without FCH. ... See full document

... The connection to ground of the supplementary equipment grounding conductor shall be in compliance with the rules for terminating bonding jumpers in Part K of Article 250 of the National Electrical Code, ANSI/NFPA ... See full document

... ND-45670 (E) CHAPTER 2 Page 33 Revision 2.0 Note 5: Announcement Service can be used to provide a voice message when an incoming C.O. line/Tie line call has been transferred and encounters a busy or ... See full document

... This card is equipped with Memory, TDSW (1024CH × 1024CH), 16-Line CFT, PB Sender, PB Receiver, Clock, PLO (slave mode 2 ports), RS-232C Ports (2 ports) for MAT/Built-in SMDR, Modem for remote maintenance, ... See full document

... Number 2 F1034 OAI Function Key Number 3 F1035 OAI Function Key Number 4 F1036 OAI Function Key Number 5 F1037 OAI Function Key Number 6 F1038 OAI Function Key Number 7 F1039 OAI Function Key Number 8 F1040 OAI ... See full document

... The maximum number of Wireless PS stations has been expanded from 168 to 250 when an Integrated type system is being used. Previously, each PS line reduced the capacity of CM10 by three ports [One port for CM1C and two ... See full document

... PFT0 26 Sta. T0 1 Sta. R0 27 4LC. T0 2 4LC. R0 28 C.O. T0 3 C.O. R0 29 4COT. T0 4 4COT. R0 30 Sta. T1 5 Sta. R1 31 4LC. T1 6 4LC. R1 32 C.O. T1 7 C.O. R1 33 4COT. T1 8 4COT. R1 34 Sta. T2 9 Sta. R2 35 4LC. T2 10 ... See full document

... The telephone company may make changes in its technical operations and procedures. If such changes affect the compatibility or use of the NEAX2000 IVS, the telephone company must provide adequate notice of the changes. ... See full document

... Before starting installation work, the installer must fill in the office data sheet and draw the system layout and floor layout in this manual according to customer’s requirements. In the course of this work, the ... See full document

... if the fault range is (c) and (d). In this case, the whole module involved is placed into make-busy status even if the fault is partial, and the station lines currently operating normally become faulty status. Diagnose ... See full document

... STEP 1: ACFO - Enable this feature by allowing CF = 3: CALL FORWARDING-INTERCEPT/ ANNOUNCEMENT. The CFI parameter will come up for assignment. An Attendant Console may be programmed so that intercepted calls can ... See full document

... The Local Partition (LP) number refers to a logical local processor number, theoretically assigned for each IMG that consists of four (or less) Port Interface Modules (PIM). Though the local processor does not ac- tually ... See full document