[PDF] Top 20 ND-46248 (E) ISSUE 2 STOCK # 151937 WCS System Manual

... the system data, provided via non-hardware supported ...the system data programming for op- erating Home PSs and Visitor PSs used for Multi-Site Roaming, together with the Virtual ... See full document

... Figure 4-11 shows sample cable connections, where HUB (PA-M96) cards are provided in a dual configu- ration and the FCH (PA-FCHA) card is located in PIM 1 (1-IMG system/IMG0). When HUB cards are pro- vided in a ... See full document

... The connection to ground of the supplementary equipment grounding conductor shall be in compliance with the rules for terminating bonding jumpers in Part K of Article 250 of the National Electrical Code, ANSI/NFPA 70. ... See full document

... the system layout and floor layout in this manual according to customer’s ...Programming Manual, Command Manual and Installation Procedure ... See full document

... In this case, if a 5-digit station number is dialed, the call is immediately connected to the called station. However, if a 4-digit station number is dialed, the call is connected to the called station with a certain ... See full document

... Note 5: When the DCE connected to the port does not provide a function to send the DSR signals, set the switch to ON. In this case, the AP00 card can not recognize the actual state of the DCE, so that the call records or ... See full document

... Provides Memory, TDSW (1024CH x 1024CH), 16-line CFT, PB sender, Clock, PLO 2 ports (receiver mode/source mode), two RS-232C ports, 2-line DAT (Recording duration: Max. 128sec.), DK, 4-line PB receiver, ... See full document

... This circuit card mainly provides the two functions: 1) collection of BLF/TGBL information (associated with Attendant/Desk Console operation) from DLKC cards of all nodes in an IMX-U system, and 2) ... See full document

... The CPU sends diagnosis data at periodic intervals to the Port Microprocessor (PM) on the FCH (PA-FCHA) cards to monitor the PM. If the CPU cannot receive the return data within a predetermined time, the system ... See full document

... Note: Up to three DAIA cards can be connected directly by a daisy chain connection on one PIM. If two or three DAIA cards are mounted on one PIM, the 17-TW-0.3 CONN CA-A is required. When the system is more than ... See full document

... (d) IP can be accommodated to multiple nodes in a Fusion Network. However, maximum number of Status Monitoring Requests to a terminal is decided by the system data (max. 8 ports available including UAP). Note that ... See full document

... mode 2 ports), RS-232C Ports (2 ports) for MAT/Built-in SMDR, Modem for remote maintenance, and Mu- sic-On-Hold tone source (Melody IC/TNT), 4-circuit PBR (for PB calling or ... See full document

... In the description of each command, initial data which is automatically loaded into memory, after system ini- tialization (using position “B” on SW3 of the MP, followed by a reset) is indicated with “ ”. Refer to ... See full document

... Event Based CCIS allows a PBX customer who does not have a tie line (or when a customer can not use the tie line due to the busy or fault of the line), to use the various CCIS feature by using the ISDN line as a CCIS ... See full document

... This feature enables a PS user to call a maximum of “20-Party (self + other 19 members)” conference, by only dialing a pre-programmed Group Calling Conference Number. If the Group Calling Conference Number is once ... See full document

... This chapter explains the procedure to verify the normal operation of the IPTRK circuit card, when installation and necessary data setting have been completed. This chapter also explains the procedures to test and ... See full document

... The Local Partition (LP) number refers to a logical local processor number, theoretically assigned for each IMG that consists of four (or less) Port Interface Modules (PIM). Though the local processor does not actually ... See full document

... • CPU Board: Includes the Main Processor Unit (MPU), flash ROM, 200 MHz clock, and 256 MB - Random Access Memory (RAM). (256 MB-RAM is used for a system using FCCS features.) In addition, the board is equipped ... See full document

... The Local Partition (LP) number refers to a logical local processor number, theoretically assigned for each IMG that consists of four (or less) Port Interface Modules (PIM). Though the local processor does not actually ... See full document

... The Local Partition (LP) number refers to a logical local processor number, theoretically assigned for each IMG that consists of four (or less) Port Interface Modules (PIM). Though the local processor does not ac- tually ... See full document