[PDF] Top 20 International Journal of Basic & Applied Sciences IJBAS-IJENS Vol:12 No:06 80

... The variance analysis gave values F count (9.4) > F table (4.1), so to conclude that the four treatments influence the muscle cell diameter differently. While the Tukey[r] ... See full document

... activated by binding Cr ions and mobilizing them into the cells. This binding results in stabilization of the active conformation of insulin receptor tyrosine kinase. Reduced insulin efficiency or insulin resistance may ... See full document

... A thermally induced phase separation technique (TIPS) was used by Ruiyun and Peter, 1999, in order to create highly porous composite scaffolds for bone tissue engineering [60]. PLLA was mixed with hydroxyapatite (HA) ... See full document

... The results showed that laser exposure raised the level of gonadotropin hormones (GtH-I and GtH-II) in blood serum 6 hours before spawning compared with the cont[r] ... See full document

... Abstract -- A device being capable of measuring particle surface charge has not been found yet. Therefore, no one is able to measure particle charge directly. A well known ammeter is only able to measure electric ... See full document

... Fig. 2 shows the three-dimensional response surface which was constructed to show the effects of activation temperature and activation time on the Zn (II) removal. It was observed that Zn (II) removal increased with ... See full document

... about 12 cm on 25 November 2007 in which in that time sea level changes induced by local wind set up and inverted barometer effect being about < 1 cm and < 2 cm, ... See full document

... Sound pressure is the adequate measure of the level of auditory stimulation in pressure-sensitive fish such as otophysines [12] in any acoustic field. For technical and comparative reasons, the hearing thresholds ... See full document

... It reveals that every factor stimulates to use ICT for effective & efficient learning. That means all factors tabulated in the table have the greater role for influence to use of ICT in TVE sector of Bangladesh. ... See full document

... Engineers collect three basic measures: size, time, and defects. Size is measured in lines of code (LOC). In practice, engineers use a size measure appropriate to the programming language and environment they are ... See full document

... also applied by Tang [3] in designing a plastic injection mould to reduce ...warpage. Basic design principles for assembly suggest that removing the fastener on the product for to reduce ... See full document

... From figure 5 above exhibited there were variations among four wood species. Paraserienthes sp. points out increasing number of conductance starting from 10Hz to 10 5 Hz. In contrast, for Anthocephalus sp. from the graph ... See full document

... For each system configuration exist a percentage change of fault level respect system's levels without DG, and this is the same change for all nodes, this behavior has been used as calculation variable for reprogram ... See full document

... Secondly, static analysis which is test of strength of car doors by applying forces at carefully selected points in various com- ponents of each door for extracting the displacement and stresses results. This can also be ... See full document

... Ishizuka, Ueno, Hattori, and Kita [11] reported that the hydration of a mix of coal fly ash, lime and anhydrite resulted in the formation of C-S-H and ettringite. Graham, Sutterer, and Robl [4] related the strength gain ... See full document

... After a two- dimensional analysis for the potential distribution under the gate and incorporating an electric field dependent mobility in the channel, the drain current expressions are[r] ... See full document

... Use local exhaust ventilation is widely used in other places such as in particular the production of industrial paints, industrial food production and equipment manufacturing industry[r] ... See full document

... The FEM modeling consists of three general steps (a) preprocessing (b) analysis (c) post processing. It is very important to carefully specify the design of the model as the quality of results depend upon the quality of ... See full document

... For the first time Fraunhofer lines asymmetry was described by a simple comparison of the vio- let and red wings of the line profiles. A little later, the profile asymmetry was characterized by bisec- tor. Further, the ... See full document

... [r] ... See full document