[PDF] Top 20 CFD Simulation of Subcooled Flow Boiling using OpenFOAM
Has 10000 "CFD Simulation of Subcooled Flow Boiling using OpenFOAM" found on our website. Below are the top 20 most common "CFD Simulation of Subcooled Flow Boiling using OpenFOAM".
CFD Simulation of Subcooled Flow Boiling using OpenFOAM
... Subcooled flow boiling in vertical channels have many industrial applications, including heat removal from core of ...work, subcooled flow boiling is simulated using open ... See full document
7
CFD Simulation of Internal Solitary Wave Using the Volume of fluid Method within OpenFOAM
... Abstract. A numerical wave tank based on OpenFOAM was developed to investigate internal solitary waves. The interface of fluids was captured by VOF method. In this paper, comparisons between numerical results and ... See full document
6
CFD modeling of a gas exchange membrane in OpenFOAM
... a simulation model of the gas exchange between the alveoli and the capillaries designed in computational fluid dynamics ...fluid flow, heat transfer and so on by utilizing computer-based ...In CFD ... See full document
65
Electrical Capacitance Volume Tomography Validation of Column Flotation Process with Gas Injection Variation
... between simulation and experiment showed in ...CFD simulation. For example, density and viscosity of the simulation are calculated based on the number of theory, while the density and ... See full document
13
Verification of ANSYS Fluent and OpenFOAM CFD platforms for prediction of impact flow
... impact flow is widely used for a very intensive drying effect of wet ...drying. CFD simulation of nozzle designs may be accepted as a technically easiest approach to find the most efficient geometry ... See full document
5
CFD Simulation of Impinging Jet Flows and Boiling Heat Transfer
... jet flow, stagnating flow and a wall jet (see ...jet, flow exiting from the nozzle interacts with the ambient flow and due to the Kelvin- Helmholtz instabilities a street of roll-up vortices ... See full document
163
Numerical Modelling of Subcooled Boiling Flow based on Mechanistic Approach: A Validation Study using Wet Steam (IAPWS) as Working Fluid Properties
... For boiling model, the proposed models, which consist of the fractal model (2002), the force balance model (1993), and the mechanistic model (2008), were examined through a CFD ... See full document
9
Numerical Simulation of Flash Boiling Effect in a 3-Dimensional Chamber Using CFD Techniques
... External flashing is difficult to obtain because a smooth nozzle entry geometry and/or low injection velocities must be used in order to avoid regions of locally low pressure inside the injection holes and to suppress ... See full document
9
Predicting Two-Phase and Subcooled Boiling Flows with a Two-Fluid CFD Boiling Model Combined with a Population Balance Approach
... predict subcooled and saturated boiling ...and subcooled boiling flow ...The boiling model is based on the heat flux partitioning approach and accommodates the heat flux due to ... See full document
9
Simulation of Reinforced Reactive Injection Molding with the Finite Volume Method
... for simulation of reinforced reactive injection molding is ...source CFD toolbox OpenFOAM, using the ...the flow front, which is a typical phenomenon of RRIM and cannot be seen in the ... See full document
16
CFD modeling and simulation of PEM fuel cell using OpenFOAM
... Fig. 4 plots the cell polarization or I-V curve. The results of the present work are compared to the results of the numerical model and experimental data reported in Yuan et al. [4] since some of the parameters and ... See full document
6
Simulation of Void Fraction Profile Evolution in Subcooled Nucleate Boiling in a Vertical Annulus with a Bubble-Tracking Model
... of subcooled nucleate boiling flow in a vertical channel at low-pressure conditions is proposed, with specific application to the case of boiling in an annulus with a central heating ...and ... See full document
9
CFD Simulation of Boiling Flows with an Eulerian-Eulerian Two-Fluid Model
... the boiling flows that are to some extent experienced in almost all water-cooled ...advanced CFD methods is progressing at a fast rate, Eulerian-Eulerian averaged two-fluid models still represent the only ... See full document
15
Modeling of void fraction and liquid temperature profile evolution in vertical subcooled nucleate boiling flow
... The relative motion between bubbles is mainly influenced by the eddy motion o f the length scale o f bubble size (Prince and Blanch, 1990). Approaches which consider the structure o f the liquid turbulence, for instance ... See full document
7
Analysis of vortex shedding in a various body shapes
... Vortex shedding is determined by two properties; the viscosity of the fluid passing over a bluff body, and the Reynolds number of that fluid flow. The Reynolds number relates inertial forces to the viscous forces ... See full document
38
Thermal Analysis on Mono-Block Type Divertor Based on Subcooled Flow Boiling Critical Heat Flux Data against Inlet Subcooling in Short Vertical Tube
... The subcooled flow boiling critical heat fluxes (CHFs) and the heat transfer coefficients (HTCs) data for the tube length, L, of 49, 99 and 149 mm with 9-mm inner diameter were applied to thermal ... See full document
10
Flow prediction in brain aneurysms using OpenFOAM
... For different resolutions profiles of the streamwise velocity at several equidistant streamwise locations are shown in Figure 4.3. Note that grids with different resolution do not have coinciding grid points, because ... See full document
57
Prediction of bubble departure in forced convection boiling: a mechanistic model
... Unal, Maximum bubble diameter, maximum bubble-growth time and bubble-growth 759 rate during the subcooled nucleate flow boiling of water up to 17.72 MN/m2, International 760 Journal of H[r] ... See full document
37
Validation of tools to accelerate high-speed CFD simulations using OpenFOAM
... Figures 7 and 8 show the progress of the solution with respect to the number of iterations. Similar results were found for pressure and y -velocity. It is evident that the LTS solver converges to the analytical solution ... See full document
18
Forced convection film boiling of subcooled water around a sphere
... liquid through the test section, a test section to contain the sphere, an induction heating unit to heat the sphere, a temperature rec.order and an optical pyrometer to measure temperatu[r] ... See full document
273
Related subjects