[PDF] Top 20 Experimental Investigation on EDM of Titanium Alloy using Taguchi Method

... levels to predict the optimal choice for each Material Removal Rate (MRR), Tool Wear Rate (TWR) and Surface Roughness(SR). L9 Orthogonal array is used to conduct Experimentation. To identify the significance of ... See full document

... The experimental investigation on P20 Die - Tool Steel reveals that the current applied and pulse-on and pulse-off duration influence the out-put of MRR and Surface Quality, [Bhaskar Reddy et ... See full document

... 4. Neeraj Sharma et.al. [4] Have discussed the significant process parameters along with the percentage contribution of each parameter. ANOVA is used to find the percentage contribution of significant process parameters. ... See full document

... Abstract - The Electro Discharge Sawing (EDS) process is a modified Electro Discharge Machining (EDM) process to obtain high material removal rates in sawing of large bar stocks and billets of high strength ... See full document

... design method is suitable to analyze the metal cutting problem by considering the optimization in end milling using S/N ratio approach and Pareto ANOVA ...Taguchi’s method for parametric design was ... See full document

... production method for machining of electrically conductive hard ...in EDM make it even more difficult to select machining conditions for optimal ...work, Taguchi Design Method is used to ... See full document

... The density of the sintered samples was measured by the immersion density method. Three readings (corresponding to the three replications) were recorded for each experimental condition as shown in Table 2. ... See full document

... of Titanium alloy ...(DOE) method for selection of optimal cutting parameters during WEDM of Titanium alloy ...studied using Taguchi ...out using Minitab 15 ... See full document

... done using commercially available finite element code ABAQUS/ ...and titanium blank were modeled as deformable volume and deform- able shell ...new method is invented in this contribution for ... See full document

... roughness using design of experiments and multiple regression method and concluded that pulse on time has significant effect on the ...process using Taguchi ...roughness using ... See full document

... Tungsten carbide alloy was the target material used in this investigation. Table 1 shows the material related properties. Experiments were performed using a Charmilles Electrical Discharge Machine, ... See full document

... In this project, the effect of WEDM parameters such as pulse on time, pulse off time, voltage and peak current are investigated on the material characteristics such as material removal rate, kerf width and surface ... See full document

... the EDM process with the multiple performance ...parameters using discharge current, gap voltage, pulse-on time and duty cycle as typical process parameters are optimized with considerations of multiple ... See full document

... the EDM process with the multiple performance ...parameters using discharge current, gap voltage, pulse-on time and duty cycle as typical process parameters are optimized with considerations of multiple ... See full document

... concrete is mixed with different percentages of titanium dioxide (0%, 0.5%, 1%, 1.5% and 2%) of powder content. According to IS 10262:2009 and IS 415:2000, the M35-grade concrete mix proportions were obtained. In ... See full document

... material. Experimental observations are based on Taguchi’s L-27 orthogonal array has been ...by using taguchi ...in EDM and compare the tool wear rate of cryogenic treated cooper and brass ... See full document

... Taguchi method which combine the experiment design theory and the quality loss function concept has been used in developing robust design of products in process and in the solving of sum taxing problems of ... See full document

... MIG welding was primarily developed as a high current-density, smaller-diameter metal- electrode process with argon shielding for welding aluminium. Hence the term MIG was appropriate and the process was equally ... See full document

... In Taguchi method, process parameters which influence the products are separated into two main groups: control factors and noise ...to Taguchi based methodology, the characteristic that the larger ... See full document

... studied EDM process parameters using Taguchi Method with Copper Electrode At peak current 12(A), pulse on time 15(μs), pulse off time 3(μs) and flushing pressure ... See full document