[PDF] Top 20 DEFINITY Enterprise Communication Server Release 8.2 Reports Guide

... hour reports can be scheduled at 15-minute intervals (that is xx:00, xx:15, xx:30, ...the reports be scheduled for off-peak ...all reports for the same hour and time interval, but stagger them across ... See full document

... a 2-wire interface to the central office (CO) public exchange for incoming and outgoing ...on DEFINITY digital voice terminals (DCP and BRI) equipped with a 32- or 40-character alphanumeric display, and ... See full document

... upgraded Release 8, then these translations must be copied to a spare tape and sent to Software Technical Support (STS) so that reports of the current G2 translations and a G3-MA diskette with basic ... See full document

... two DEFINITY ECS systems. H.323 trunk groups can be configured as DEFINITY-specific tie trunks supporting ISDN trunk features such as DCS+ and QSIG, or as generic tie trunks permitting interconnection with ... See full document

... 3. Return the SPE-SELECT switches to their previous locked position. When the standby is back up and cycling, the yellow LED on the Processor circuit pack will begin flashing. It is then safe to unlock the SPE-Select ... See full document

... g. Error Type 1025 - FPGA failure. This failure indicates a problem on the FPGA device located on the TN2302. The last byte of the inline error gives a hint as to the problem with the FPGA. The diagnostic strategy for ... See full document

... Layer 2, or the data-link layer , refers to code created and interpreted by the DCE. The originating equipment can send blocks of data with the necessary codes for synchronization, error control, or flow control. ... See full document

... This command places all maintenance objects associated with a property management system link in the maintenance busy state. No periodic or scheduled maintenance is performed on the busied out maintenance objects until ... See full document

... 2. The field QSIG Value-Added Lucent shall be selected as y and Supplementary Service Protocol Option shall be selected as B on a Trunk Group form to send QSIG-VALU Call Coverage MSI information to a remote switch ... See full document

... Resetting the Release 7r with either the reset system 4 or reset system 5 commands breaks down and then re-establishes the PPN-to-EPN links during the reset sequence. Since these links may be down longer than 3 ... See full document

... terminators, and the Inter-Cabinet Cables (ICC). If a FAIL Result code is seen or other problems are indicated, check these cables. If problems persist, refer to DEFINITY Enterprise Communications ... See full document

... Event Reports) will be provided to the applications regardless of whether link version 1, version 2 or version 3 is ...by DEFINITY ECS is that new ASAI messages that were unsolicited by the adjunct ... See full document

... 1. Check the port of interest. If it is not configured for UNI signaling, then the port was administered for no UNI signaling. Verify that signaling is UNI3.1 2. The connect, setup, and release message ... See full document

... agent, trunk access code, VDN, announcement, or data extension, the address field may contain the extension number (in ASCII). 1 In an incoming Domain IE the ECS will parse, the only ASCII characters the ECS permits are ... See full document

... Generally, the term DCE is applied to devices that mediate between customer equipment and the carrier or network. Such devices include modems, data modules, and data units. DTE describes devices that provide a user ... See full document

... The DEFINITY ECS offers a wide range of features and functions. Some of these you can administer differently from one user to the next. For example, you can give one user a certain set of phone buttons, and the ... See full document

... Acceptable Water Pipe — A metal underground water pipe, at least 1/2-in. (1.3 cm) in diameter, in direct contact with the earth for at least 10 ft (3 m). The pipe must be electrically continuous (or made ... See full document

... DEFINITY ECS allows you to modify the permissions associated with a login. The system maintains default permissions for each level of login, but you may want to further restrict the login, or at least make sure ... See full document

... To maximize voice quality using IP Solutions, you must consider both your hardware and network configurations. For example, with IP Softphones, you can send the audio over traditional circuit switch lines, providing high ... See full document

... Multi-site applications work similarly, but additional administration is required. Since steps in a multi-site BSR vector will contact one or more remote locations, you need to define these locations, tell ... See full document